Announcement

Collapse
No announcement yet.

'81 GS550 Cafe Build

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Wow! The bike looks incredible!

    Comment


      Really really really nice.
      http://img.photobucket.com/albums/v5...tatesMap-1.jpg

      Life is too short to ride an L.

      Comment


        Just stumble across this build. Wow, D-Mac! That looks beautiful! Now I gotta go back and read from the start! I like the single carb filter. Wonder how that works over individual carbs.

        Whoops! After an hour or two of reading the thread, just noticed they are dual filters. Forgot K&N made those.
        Last edited by Guest; 12-24-2012, 11:47 PM.

        Comment


          Before……



          After……

          Comment


            Originally posted by Road Rash View Post
            Just stumble across this build. Wow, D-Mac! That looks beautiful! Now I gotta go back and read from the start! I like the single carb filter. Wonder how that works over individual carbs.
            Thanks!

            These K&N filters come as a pair (1&2 and 3&4 carbs are linked). I've heard that they are much better than the separate pods. We'll see though. They were expensive and not the easiest to fit.

            Comment


              Nothing other than incredible!!!

              Comment


                Really inspiring job. I'm not going the cafe route but I like how clean your bike ended up. Are you going to have any rear fender? If not how are you going to keep the underside clean? Just lots of elbow grease?

                Comment


                  Originally posted by MAJikMARCer View Post
                  Really inspiring job. I'm not going the cafe route but I like how clean your bike ended up. Are you going to have any rear fender? If not how are you going to keep the underside clean? Just lots of elbow grease?
                  Great question. I toyed with the idea of welding on some mounts for a removable rear fender (a cover behind the mid compartment I could add/remove as needed). If I was going to ride this thing much (or at all in the wet) I would really want that - or at least something in hard plastic or aluminum that I could zip-tie in place.

                  I don't plan to use this bike as my daily rider, or much at all really (my BMW RT serves that purpose - I don't even wash that bike!) The GS will be strictly for dry, sunny days on back roads. If it gets to be a chore to clean, I'll likely do some modifications at some point. In that case, a front fender would probably be a good idea too.

                  For now, it's an incredibly practical engine in an incredibly impractical frame.

                  Comment


                    I fabbed a splash shield for my old bike, to keep things clean. Just some aluminum sheet metal, painted black to blend in, rivited to the underside of the backhalf of the frame.
                    Last edited by Guest; 12-24-2012, 11:52 PM.

                    Comment


                      Congratulations mate, that is an amazing achievement!! One of the best executed projects I've seen in a good while. I'm also loving the area where you have the bike photographed, sort of a cafe themed chill-out area.... no doubt where the 550 and future projects will hang out!?

                      Any plans to upgrade the bike further - a project is never finished

                      Be great to get a vid of the old girl up and running too...

                      Dec

                      Comment


                        Gorgeous bike D-Mac! I have been watching the build form the get go and insanely impressed with the way it has turned out! One thing I have seen several people do is take a piece of plexiglass and have it run on the tail support tube in front of the rear tire to keep any unwanted debris from being flung on the underside of your bike. Easy to remove and clean if you ever want to put it in a bike show

                        Also have you ever thought of running an 18" rear? Again awesome build!

                        Comment


                          Simply beautiful! Incredible job. Hats off!
                          1983 GS1100E

                          Comment


                            An amazing transformation from where you started. Hard to believe it's the same bike. Very nicely done. You should be very proud.

                            I was faced with the same dilemma on a sub-fender for my Honda 550. I used a plastic front fender from a Yamaha RD400, and fabbed a reverse mount for it that attached to the swing arm. This, after cutting it in half down the center with a band saw and then widening it an inch with a piece of aluminum. It was riveted back together and then fiberglassed to smooth it all out. What a pain. It looked really cool and worked..for the most part..but it also hit the bottom of the seat pan under heavy compression. I took it off, bought a small sheet of black plastic 1/8" thick, cut it to fit the frame opening behind the airbox, drilled a couple of holes on each side and used black zip ties to mount it to the frame tubes. Works great. I must've spent three days on the first mod, only to find out the sheet of plastic was the easiest and simplest way to do it, and it looks good, too. Sometimes we have a tendency to over-think things... It's one of the things I like best about your bike. It has a very clean and uncluttered look to it. Again, nicely done.
                            1979 GS1000S,

                            1982 Honda CX500 Turbo, 1982 Honda MB5 w/CR80 motor, 1977 Honda "nekid" Goldwing, 1976 Honda CB550F cafe', 1972 Honda XL250 cafe'

                            Comment


                              wow what a transformation from the redneck rocket... and the photos are equally artistic... you sir have talents!
                              GS850GT

                              Comment


                                Your bike and the work you have put in it is very inspiring.
                                Every shiny bit shows the dedication and attention in your work.
                                Congratulations on a job done so well!

                                Comment

                                Working...
                                X