Announcement

Collapse
No announcement yet.

Progress!!! 1978 GS1000E Restoration/Performance Rebuild

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    That looks great!!

    Originally posted by philosopheriam View Post
    So, I tried to polish the original lower triple cover and it just didn't look that good - the plastic was graying and the chrome accents were dulled/scratched/faded in several places. So, I did a little garage paintwork...

    Scuffed and masked



    Final finish: x2 coats Rust-Oleum gloss black plastic paint and x2 coats Rust-Oleum chrome/silver




    I scuffed the piece with steel wool and then masked it - the gloss black was laid first. After letting the piece dry for about 5 days, I then masked everything but the raised lines - I used a roll of 1/8" wide 3M painters tape to fit in-between each raised line. I then scuffed the existing gloss black paint to give it a good "key" so the chrome/silver would adhere properly. Two coats of silver, one hour of dry time, and then I removed all the masking tape. I will let the piece dry for several days and then I will put it outside in the sun to make sure the paint cures well.
    82 gs1100e FAUX Skunk
    80 gs1000s

    Comment


      This build is absolutely sweet....don't know if you've lived in town long enough to remember, but the Saturday night Lake street cruise meets have started again in front of Ace Hardware down from the big S sign...they start to gather around 8-9pm and stay till 11ish. Maybe you could swing down some time when she's done soon - I'd love to see that bike in person!

      Comment


        What's going on now Anthony?????
        Ray.

        Comment


          Originally posted by rapidray View Post
          What's going on now Anthony?????
          Ray.
          Well, in response to your question, I got my butt in gear and made some decent progress today :-) !!!

          Built a stand to elevate the frame while I'm installing the suspension
          IMG_1602 by Anthony Monteleone, on Flickr
          IMG_1603 by Anthony Monteleone, on Flickr
          IMG_1604 by Anthony Monteleone, on Flickr

          I installed the steering stem races last week, and this week's goal was to install the triples and forks
          IMG_1605 by Anthony Monteleone, on Flickr
          IMG_1606 by Anthony Monteleone, on Flickr
          IMG_1607 by Anthony Monteleone, on Flickr
          IMG_1608 by Anthony Monteleone, on Flickr
          IMG_1609 by Anthony Monteleone, on Flickr
          (I ended up taking the stand off the rolling dolly - the frame was a bit too high for my liking. The above arrangement is better.)





          Next weeks objectives are:
          1. Build a non-marring driver to install the shock bushings into the swingarm - I will use this driver to install the bushings into the footpegs, as well.
          2. Get the swingarm and rear suspension installed
          Last edited by philosopheriam; 12-30-2017, 12:04 PM.
          Cogito ergo sum - "I think, therefore I am"
          René Descartes

          Comment


            Originally posted by 80GS850GBob View Post
            This build is absolutely sweet....don't know if you've lived in town long enough to remember, but the Saturday night Lake street cruise meets have started again in front of Ace Hardware down from the big S sign...they start to gather around 8-9pm and stay till 11ish. Maybe you could swing down some time when she's done soon - I'd love to see that bike in person!
            Hey buddy - didn't mean to ignore your post. I've lived in Aurora since 2008, and I first moved to Naperville in 2004. Right now, I'm near New York and Eola - the west side of the Fox Valley mall. It sound's crazy, but I don;t really venture into downtown Aurora too much, aside from going to Ballydoyle's from time to time. Trust me, when the bike is done it will be the proud attendee of many a cruise night!
            Cogito ergo sum - "I think, therefore I am"
            René Descartes

            Comment


              I'm on mountain near ohio. Nice bar - street parking's a P.I.T.A. though, due to the riverboat, but there's always the parking garage.
              I'm currently prepping tail and side panels for paint, along with other needed things, in hopes to have her done by spring.
              Eons ago the riverwalk was quite the cycle hang out...not sure they do that any more though.

              Comment


                More progress!!! Felt motivated today

                The patented "no marring" bushing driver - the washer that rests against the backside of the swingarm (or footpeg, etc - the piece you don't want to scratch or destroy the paint/powdercoat) is wrapped in several layers of duct tape. The washer that rests on the face of the bushing was ground down so the OD is a hair smaller than the OD of the bushing, and the ID of the washer is just large enough to allow the center sleeve of the bushing to sit inside it. The entire assembly worked like a charm :-)
                IMG_1632 by Anthony Monteleone, on Flickr
                IMG_1631 by Anthony Monteleone, on Flickr

                Got the rear swingarm and suspension installed - only ran into a few small problems, i.e. I had to remove some of the powdercoating on the swingarm bearing seal surfaces and the areas in the frame that the seals sit against. Not a big deal, but the extra thickness of the powdercoating was causing some clearance issues. All fixed with a bit of emery cloth and an angle die grinder with a 3m facing disc.
                IMG_1629 by Anthony Monteleone, on Flickr
                IMG_1633 by Anthony Monteleone, on Flickr
                IMG_1630 by Anthony Monteleone, on Flickr

                Also got the front wheel, front wheel bearings, and rotors/calipers installed - noting is super tight, as this is a test fit for clearances, etc. However, everything seems to line up fantastic. Salty's brake upgrade seems to work like a charm. I purchased the rotors (forgot which ones) that had the correct bolt pattern yet the holes simply needed to be enlarged to 8mm. I did this on my drill press and it came out great.
                IMG_1628 by Anthony Monteleone, on Flickr
                IMG_1635 by Anthony Monteleone, on Flickr
                Last edited by philosopheriam; 12-30-2017, 12:08 PM.
                Cogito ergo sum - "I think, therefore I am"
                René Descartes

                Comment


                  Also installed the front sprocket - a JT sprocket for a 530 conversion
                  IMG_1634 by Anthony Monteleone, on Flickr

                  And the final product!
                  IMG_1626 by Anthony Monteleone, on Flickr
                  Last edited by philosopheriam; 12-30-2017, 12:09 PM.
                  Cogito ergo sum - "I think, therefore I am"
                  René Descartes

                  Comment


                    Sure looking sweet!
                    https://drive.google.com/open?id=0B9zH8w8Civs8ejBJWjdvYi1LNTg&resourcekey=0-hlJp0Yc4K_VN9g7Jyy4KQg&authuser=fussbucket_1%40msn.com&usp=drive_fs
                    1983 GS750ED-Horsetraded for the Ironhead
                    1981 HD XLH

                    Drew's 850 L Restoration

                    Drew's 83 750E Project

                    Comment


                      Originally posted by jsandidge View Post
                      Sure looking sweet!
                      The rear wheel is on the docket for next week!
                      Cogito ergo sum - "I think, therefore I am"
                      René Descartes

                      Comment


                        Looking GOOD!!!!
                        Ray.

                        Comment


                          Originally posted by philosopheriam View Post
                          Also installed the front sprocket - a JT sprocket for a 530 conversion

                          Where's the spacer?It goes on the outside of the sprocket.

                          Comment


                            Put the COMPLETE rear wheel assembly on, with the sprocket so you can pull a string to check front & rear sprocket alignments.
                            Ray.

                            Comment


                              To my knowledge, when doing a 530 conversion, the spacer goes behind the sprocket to move it outward. The 530 sprocket is nearly 1/4" thinner at the center than the original 630 sprocket. Before I install the chain, I will check for alignment nonetheless...
                              Cogito ergo sum - "I think, therefore I am"
                              René Descartes

                              Comment


                                You will be moving the spacer to the outside.It seems counter intuitive but that's how it goes.

                                When I got my 530 front from Katman that was his instructions and I've read it here as well.Don't forget the 530 sprocket rear is thinner to.

                                Comment

                                Working...
                                X