Announcement

Collapse
No announcement yet.

1981 gs750 (gs750e) Retro Racer project

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    And this is how they turned out:



    Comment


      Also got the front tyre onto the rim today:

      Comment


        I removed the old bearings from the stem, and was about to press the new lower bearing on. The bearings are conversion bearings from All Balls. In the package was these two spacers. They are about the same with as the stem, and I'm not sure where they go.. Anyone who knows? There a two spacers in the pack with the lower bearing (tapered bearing) and two in the pack with the upper bearing.

        The spacers look like this:

        Comment


          Originally posted by LarsKroghStea View Post
          I removed the old bearings from the stem, and was about to press the new lower bearing on. The bearings are conversion bearings from All Balls. In the package was these two spacers. They are about the same with as the stem, and I'm not sure where they go.. Anyone who knows? There a two spacers in the pack with the lower bearing (tapered bearing) and two in the pack with the upper bearing.

          The spacers look like this:

          Well, I'replying to my own post I found this in an old post from 2006, so it's strange that my kit didn't include instructions. Maybe they're online somewhere.

          "This kit is supplied with (2) spacers that are used by various applications
          to make up for thickness differences between the taper bearings and the ball
          stacks.

          We have put instructions for the use of these spacers in kits since last
          year, but if you have an earlier kit there may not be any instructions.

          To determine which, if any washer is required measure the stack height of
          the ball bearing assemblies (place a few ball between the races of both the
          top and bottom bearing sets) and compare this measurement to the stack
          height of both taper bearings. Select a washer to put the difference in
          stack height to 1 mm. If the stack height is already within 1 mm then do
          not use any washer.

          The washer will be placed onto the stem first (before the seal and taper
          bearing)

          We do have some swing arm kits for street applications, but not a complete
          line. If you can supply us with the dimension of the components we can
          typically supply all or some of the parts.

          Regards
          Kevin"

          I'll put the stem in the freezer until I get to measure the old bearings

          Comment


            Right side controls finished, I think it works well together with the throttle assembly;


            Comment


              That is some slick fab work. Will there be labels? Or will you just have to remember what button does what on the left and right hand controls?
              Rich
              1982 GS 750TZ
              2015 Triumph Tiger 1200

              BikeCliff's / Charging System Sorted / Posting Pics
              Destroy-Rebuild 750T/ Destroy-Rebuild part deux

              Comment


                Nice work! Btw, where did you get your clutch lever/perch? I'm currently looking to replace the OEM ones on a few on a bikes, to get more adjustment range.
                #1: 1979 GS 550 EC "Red" – Very first Bike / Overhaul thread        New here? ☛ Read the Top 10 Newbie mistakes thread
                #2: 1978 GS 550 EC "Blue" – Can't make it a donor / "Rebuild" thread     Manuals (and much more): See Cliff's homepage here
                #3: 2014 Moto Guzzi V7 II Racer – One needs a runner while wrenching
                #4: 1980 Moto Guzzi V65C – Something to chill

                Comment


                  Originally posted by Rich82GS750TZ View Post
                  That is some slick fab work. Will there be labels? Or will you just have to remember what button does what on the left and right hand controls?
                  Thanks I'll use these printed controls for a couple of months, until the cnc-router is finished. I think that's a cost effective way to try it out, and make changes if someting doesn't work as intended. I have some aluminum pieces from an earlier project, and I'll mill aluminum versions to replace the plastic controls. I bought an anodizing kit some years ago that I haven't tested. I have a buddy with a laser engraver, and I want to try to engrave labels on the anodized aluminum with that. The engraved text turns white as the laser oxidizes the anodizing (or something like that..).

                  I'll embed a video you can see what I mean:



                  Knowing myself, this won't be happening soon, so I guess I'll borrow the wives labelmaker or something like that

                  Comment


                    Originally posted by roeme View Post
                    Nice work! Btw, where did you get your clutch lever/perch? I'm currently looking to replace the OEM ones on a few on a bikes, to get more adjustment range.
                    Thanks! These are "Accossato Folding Clutch Lever Assembly Part Number : 1400N" bought from "Bikers Discount Store" in the UK. These are "Non-RST/NRST" witch mean they don't have the "lightening eyelet" - a hole near the hinge (the hinge keeps them from breaking if you scrape the bike) that makes it lighter. They are quite pricey but high quality. I don't think I would spend that much on a clutch lever if i didn't care about matching the looks of the brake lever.



                    I paid 115£ for the clutch-perch/lever assembly. Accossato licence their brake masters from Brembo and are similar in quality to Brembos Racing Lineup (both suppliers have a cnc-version that the teams use and that version is stupidly expensive). The reason I didn't buy Brembo is that they only have hydraulic clutchlvers in their racing lineup.

                    Hope this was some useful info

                    Comment


                      Looking good!
                      1980 GS1000G - Sold
                      1978 GS1000E - Finished!
                      1980 GS550E - Fixed & given to a friend
                      1983 GS750ES Special - Sold
                      2009 KLR 650 - Sold - gone to TX!
                      1982 GS1100G - Rebuilt and finished. - Sold
                      2009 TE610 - Dual Sporting around dreaming of Dakar..... - FOR SALE!

                      www.parasiticsanalytics.com

                      TWINPOT BRAKE UPGRADE LINKY: http://www.thegsresources.com/_forum...e-on-78-Skunk/

                      Comment


                        Went on to remove the old fork and bearings today. PO had replaced the old bearings with tapered bearings and the lower bearing (the part that sits in the frame) was a real headscratcher.. the angle is such that a screwdriver will not catch the edge. I tried to make an ad-hoc tool:



                        Didn't work so well..:




                        Then I tried this:



                        Small cut with a hacksaw.



                        Pushed the tube up through the frame, took a punch and hammer, and bent all the tabs outwards. Went full sircle two/three times with light force. Gave the tube a few blows with a hammer and the bearing dropped to the floor. No scratches in the frame. Much easier I think than heating the frame with a torch (and burning the paint), welding the bearing (shrinking by heat), grinding it with a Dremel or other tips I found on the web.

                        Comment


                          The instructions for the All Balls conversion say to measure the old and the new lower bearing, and shim the difference if they are more than one mm apart.
                          Here's the old one:


                          And here's the new. No need for spacers:

                          Comment


                            I think those of you that have followed my build noticed early on that I didn't have much mechanical experience. It's mostly trial and error, and lots of research in advance. I keep at it because I really enjoy the process. I think I'm getting better at it and when enough time and effort is applied, nice things appear

                            Today I got a reminder that I'm still a newbie at many things. I read online that if you put the stem in the freezer, the bearing should "slide on without much effort". Can't say it did. I couldn't press it on by hand anyway. Adding to that, after a couple of minutes in room temperature frost appeared on the stem because of humid air. I don't want to trap all that moisture behind the bearing, so I'll wait for it to dry. Lesson learned.. Maybe this works for stem/bearing combos with less size difference. I have access to a press at my dads house, but it's an hour away. I want to see the fork on today, so I think I'll just use the old bearing and a tube and hammer it down. Here's picture of the frosted stem, straight from 20 celcius below zero (-4F)

                            Comment


                              Finally! I think I'm happy with the looks. I've been so afraid that something would be wrong with the front setup I've chosen. Either that the wheel would be too big, there would be too little ground clearance or that the wheel would be too close to the exhaust. The front is still incomplete, as it's missing fender, the headlight sits about 6-7cm too high, the brake rotors and brake lines are not there and so on. But I think the geometry is fine The gap between tire and exhaust is about 7cm. I think max travel for these forks are 12cm, but that's under really hard load. I'll drop the forks 12cm and measure the clearances.


                              Also, I always pictured the fork legs painted black, but now I think I might keep them anodized gold? What do you guys think?














                              I'll take some better pictures with the seat on soon

                              Comment


                                Moved the headlight lower and liked the look. Also did a quick photoshop of the fork when compressed (like the Photoshop pro I am.. ). It seems the fender will touch the lower clamp just before the tyre hits the exhaust. I need to set compression and preload so this doesn't happen, but I don't think it'll be a problem. I'll also hook up a GoPro for the first few rides to see how the fork behaves.



                                Comment

                                Working...
                                X