I'm off to Napa now to get some new crimps for spark plug wire. I have this cool fabric spark plug wire that matches my wiring loom that we checked for shielding and it does have it. I will be trying these on the bike and see how it runs then. I might not get to it today though because the family is going to see Birds of Prey at 2:45. I'll keep you all posted. This is crazy stuff.
Announcement
Collapse
No announcement yet.
JohnnyL's 1980 GS550L Cafe Build
Collapse
X
-
Ok. Brian just left. He brought his nifty electronic meter that also measures EMF(I think). We could probably ghost hunt with it. LOL. The bike was giving off a tremendous amount of noise(Maybe Brian can explain this better). Brian then checked my Dyna ignition wires for resistance and shielding they had none. Apparently they're supposed to have some? Anyway....the spark plug wires were giving off so much interference that they were throwing off all sorts of things. The gauge on the bike would blink and we hooked up a timing light to watch the light pattern and it was inconsistent therefore throwing off the spark. This would cause backfire in the carbs and exhaust. Crazy shyte!
I'm off to Napa now to get some new crimps for spark plug wire. I have this cool fabric spark plug wire that matches my wiring loom that we checked for shielding and it does have it. I will be trying these on the bike and see how it runs then. I might not get to it today though because the family is going to see Birds of Prey at 2:45. I'll keep you all posted. This is crazy stuff.Last edited by JohnnyL; 02-09-2020, 01:56 PM.1969 Honda CL350 Cafe
1980 Suzuki GS550L cafe project Link
2019 Yamaha MT-09
2016 Honda CBR650F(wife’s bike)
2001 Honda CBR600F4i(Son's bike)
-
I can't see clearly on that last pic of the bike in the yard, whether you have resistor plug caps or not. If you don't, you'll have to use resistor plugs, although for all I know you may already have done that.
The resistors in the HT leads (or caps, or plugs) keep the RF interference way down, compared to non-resistored leads, caps, plugs. Non-resistored HT circuits cause mayhem to onboard electronics.
You only need to put the resistance in one place - lead, cap or plug, not more than one, else all you do is rob spark energy.
I'm in the same boat - got a set of ultra-nifty plug leads with factory caps that I was loathe to chop off, so I fitted resistor plugs, namely BR8ES, which have an inbuilt 5Kohm resistor.
Actually, I regard it as a good thing, because resistor plug caps often get ignored and forgotten about for far too long, whereas now I get a new set of resistors every plug change.---- Dave
Only a dog knows why a motorcyclist sticks his head out of a car window
Comment
-
Originally posted by Grimly View PostI can't see clearly on that last pic of the bike in the yard, whether you have resistor plug caps or not. If you don't, you'll have to use resistor plugs, although for all I know you may already have done that.
The resistors in the HT leads (or caps, or plugs) keep the RF interference way down, compared to non-resistored leads, caps, plugs. Non-resistored HT circuits cause mayhem to onboard electronics.
You only need to put the resistance in one place - lead, cap or plug, not more than one, else all you do is rob spark energy.
I'm in the same boat - got a set of ultra-nifty plug leads with factory caps that I was loathe to chop off, so I fitted resistor plugs, namely BR8ES, which have an inbuilt 5Kohm resistor.
Actually, I regard it as a good thing, because resistor plug caps often get ignored and forgotten about for far too long, whereas now I get a new set of resistors every plug change.
This is driving me nuts. The mis-firing seems to only be happening on cylinders 1 & 4 and not 2 & 3. I might start the bike and video the timing light in slow motion to see if there is any sort of pattern to the mis-fire. I also will probably run down to Napa and see if they have the BR8ES resistor plugs.1969 Honda CL350 Cafe
1980 Suzuki GS550L cafe project Link
2019 Yamaha MT-09
2016 Honda CBR650F(wife’s bike)
2001 Honda CBR600F4i(Son's bike)
Comment
-
Amazingly....the NGK BR8ES plugs smoothed out the ignition. No more backfiring through the pipe or carbs. The bike sits there and purrs like a kitten. I'm still getting some sort of feedback through the RPM signal wire though. The RPM signal wire is attached to the output side of one of the coils. This causes the LCD data on the screen to flicker/pulsate. I don't know if some sort of RPM signal filter will help with this or not. I have emailed Acewell and am waiting for a response to this issue. The good news is that the bike is idling well and now I believe I can move on to jetting the carbs.1969 Honda CL350 Cafe
1980 Suzuki GS550L cafe project Link
2019 Yamaha MT-09
2016 Honda CBR650F(wife’s bike)
2001 Honda CBR600F4i(Son's bike)
Comment
-
A solid frame ground is essential to everything getting proper voltage. I can't be sure this will solve ALL of your woes, but I'll bet it will be your coil and spark issue. Either way, it is a necessity. I don't think your plug wires were an issue.
I don't think you will be too far out with the #117 jets. You will need to raise your needles, and like Steve said, start at 2.5-3 turns out on the mixture screws, and fine tune from there.'83 GS 1100T
The Jet
sigpic
'95 GSXR 750w
The Rocket
I'm sick of all these Irish stereotypes! When I finish my beer, I'm punching someone in the face ! ! !
Comment
-
---- Dave
Only a dog knows why a motorcyclist sticks his head out of a car window
Comment
-
Originally posted by Grimly View PostThis might be all you need for the tacho signal - it's probably spiky and dirty.
https://www.glowshiftdirect.com/tach...signal-filter/
1. Removed Dyna coils and put OEM coils and wires back on. Still misfiring on 1 & 4
2. Checked connections where Dyna ignition connects to coils. Still misfiring on 1 & 4
3. Disconnected the battery and ran off of another battery. Still backfiring on 1 & 4
4. Disconnected the stator and ran off of another battery. Still backfiring on 1 & 4
5. Disconnected everything(lights, gauges, etc.) from the M-Unit except the ignition. Still backfiring on 1 & 4
Mind you, dynamic timing has been done and at idle, the light is right on the F mark on the timing advancer. It idles good minus the popping through the carbs and exhaust. I put the timing light on a black surface and just watched the light flash pattern on 1 & 4. Steady flash and then skips a flash every once awhile(hence backfire). 2 & 3 have a steady flash with no skipping.
I'm running out of things to try. Any suggestions? Anyone? I'm about to call an exorcist.1969 Honda CL350 Cafe
1980 Suzuki GS550L cafe project Link
2019 Yamaha MT-09
2016 Honda CBR650F(wife’s bike)
2001 Honda CBR600F4i(Son's bike)
Comment
-
I think I zero'd in on the problem. The Dyna ignition requires a spacer to be installed on the timing advance magnet. I originally had the spacer installed but noticed that I couldn't freely advance the cam(it was too tight) so I took it off. But it seemed like there was too much movement of the cam allowing it to maybe miss a spark. I ended up milling the spacer down by about 30 thousandths and now it fits nicely. The backfiring seems to be gone but I'm not sure that it is firing at all on 1 & 4. I have spark at those spark plugs but the exhaust temp on 1 & 4 was 200 while the exhaust temp at 2 & 3 was 400. Something is wrong. Timing is dead on. Bike idles nicely with no backfiring or popping but it just doesn't sound right. It idles for a little bit and then dies. And as soon as I grab the throttle, it boggs like it's only running on two cylinders.
1969 Honda CL350 Cafe
1980 Suzuki GS550L cafe project Link
2019 Yamaha MT-09
2016 Honda CBR650F(wife’s bike)
2001 Honda CBR600F4i(Son's bike)
Comment
-
Assuming a good 12V feed to the ignitors... make sure with a meter.
To rule out a weak coil, swap the coils over.
If the fault doesn't follow the coil, suspicion falls on the ignitor. Not unknown for these Dyna ignitors to fail not long out of the box and lead to much head-scratching. Dyna are well aware of this and replace them quickly.---- Dave
Only a dog knows why a motorcyclist sticks his head out of a car window
Comment
-
Update to where I am right now.
1. I currently have the OEM coils and plug wires on the bike.
2. I have checked all voltages at the coils. All good.
3. I have switched the coils from right to left. Still burping and farting on 1 & 4
4. I have checked the timing dynamically and still see a skipped spark every once and awhile on 1 & 4.
I have diagnosed the bike as having atrial fibrillation. The next stop is with a cardiologist.
In all seriousness, I can only think that the problem lies with the Dyna ignition. I have ordered a new one though Z1 and will slap it on when I receive it. If it solves the problem, I will return the defective one for a refund. I have also ordered some tools to allow me to sync the carbs. I ordered a Morgan Carbtune, a pair of Motion Pro long nose snap ring pliers to allow me to raise the needle height and a carb adjustment tool for syncing the carbs(screwdriver/wrench). I also ordered an adjustable RPM signal filter from KOSO North america and some 107.5 and 110 main jets. I'm hoping the RPM signal filter will clean up the signal coming from the coils to the gauge and stop the blinking.
I'm really hoping the poltergeist in this bike is the Dyna ignition being defective. I can't move onto tuning this bike until I figure out why it's missing a spark on 1 & 4. Once that is figured out, I can move onto syncing the carbs and tweaking the jets and needle heights.
Ugh.....1969 Honda CL350 Cafe
1980 Suzuki GS550L cafe project Link
2019 Yamaha MT-09
2016 Honda CBR650F(wife’s bike)
2001 Honda CBR600F4i(Son's bike)
Comment
-
I was going to wait to post pics of the tins until after I put them on the bike but I am so excited about how these turned out that I have to show you now. The painter sent these to me earlier today. I pick them up tomorrow. I wasn't sure if I was going to like the matte finish but OMG....It looks better than I even imagined it would.
1969 Honda CL350 Cafe
1980 Suzuki GS550L cafe project Link
2019 Yamaha MT-09
2016 Honda CBR650F(wife’s bike)
2001 Honda CBR600F4i(Son's bike)
Comment
-
Really nice. And good luck with getting the electric gremlins out with a new dyna system.Larry
'79 GS 1000E
'93 Honda ST 1100 SOLD-- now residing in Arizona.
'18 Triumph Tiger 800 (gone too soon)
'19 Triumph Tiger 800 Christmas 2018 to me from me.
'01 BMW R1100RL project purchased from a friend, now for sale.
Comment
-
Originally posted by alke46 View PostReally nice. And good luck with getting the electric gremlins out with a new dyna system.1969 Honda CL350 Cafe
1980 Suzuki GS550L cafe project Link
2019 Yamaha MT-09
2016 Honda CBR650F(wife’s bike)
2001 Honda CBR600F4i(Son's bike)
Comment
-
Looks great! Can't wait to see them on the bike.Ron
When I die, just cremate me and put me in my GS tank. That way I can go through these carbs, one more time!https://www.thegsresources.com/_forum/core/images/smilies/cool.png
1978 GS750E - November 2017 BOTM
1978 GS1000C - May 2021 BOTM
1982 GS1100E - April 2024 BOTM
1999 Honda GL1500SE
Comment
Comment