.png "Powered by vBulletin")
Just watched an interesting video, just google mixing baking soda with super glue. Of course it's just a video and very possibly BS, like a lot of other stuff. That being said he did make it look impressive, and explained the chemical reaction between the 2 made it a lot stronger than the glue alone. The demonstrations he showed made me think possibly a good fix for cracked side covers or broke mounting studs on them. Just looked interesting and wondered if anyone has seen or tried it?
-
1983 GS1100E, 1983 CB1100F, 1991 GSX1100G, 1996 Kaw. ZL600 Eliminator, 1999 Bandit 1200S, 2005 Bandit 1200S, 2000 Kaw. ZRX 1100 -
I used this regularly when building RC airplanes back in the day. The baking soda is basically a filler, which allows fillets and such to be built up. It can also be used to fill gaps between pieces.Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection -
With Gap Filling Crazy glue, and the accelerator fluid, why would you need to go that route? I made a stupid mistake and put a heavy duty screwdriver on my '73 M.G> Midget alternator pulley, and a chunk came out. Using Gap Filing Crazy Glue, I put it on the pulley and the piece, which fit perfectly back together. A couple of drops of accelerator fluid, and it was hard as a rock, I built it up till it looked solid enough. 10K miles on it so far, I don't think it will ever come apart.
Comment
-
Several demo's in the video, but don't remember anything about filling gaps. Most impressive was they glued 2 like pieces of plastic, to a plastic board, one with the baking soda and one without. When both were cured, they bent the one without baking soda over and the glued joint broke, then bent the other over and the piece of plastic broke and the glued joint was still in tact. I brought it up down at the store and a couple folks had heard of it, but none of them had tried it yet.1983 GS1100E, 1983 CB1100F, 1991 GSX1100G, 1996 Kaw. ZL600 Eliminator, 1999 Bandit 1200S, 2005 Bandit 1200S, 2000 Kaw. ZRX 1100Comment
-
Another useful mix is silicone sealer and baking soda.
Google 'Sugru' and you'll find a commercial variant of it.
My stator wires are exiting the casing with a repaired grommet using such a mix.---- Dave
Only a dog knows why a motorcyclist sticks his head out of a car windowComment
-
Tried doing this...........set so fat i couldn't even get a mix going........Maybe using the wrong superglue...............FailOriginally posted by rphillips View PostComment
-
I use Hamburger Helper (9 parts) and finely ground squirrel meat (1 part).
1982 GS1100E V&H "SS" exhaust, APE pods, 1150 oil cooler, 140 speedo, 99.3 rear wheel HP, black engine, '83 red
2016 XL883L sigpic Two-tone blue and white. Almost 42 hp! Status: destroyed, now owned by the insurance company. The hole in my memory starts an hour before the accident and ends 24 hours after.Comment
-
rob.... Go back to sleep !!!1983 GS1100E, 1983 CB1100F, 1991 GSX1100G, 1996 Kaw. ZL600 Eliminator, 1999 Bandit 1200S, 2005 Bandit 1200S, 2000 Kaw. ZRX 1100Comment
-
Squirrel meat. A hazelnut in every bite.Originally posted by Rob S. View PostI use Hamburger Helper (9 parts) and finely ground squirrel meat (1 part).---- Dave
Only a dog knows why a motorcyclist sticks his head out of a car windowComment
Comment