Announcement

Collapse
No announcement yet.

Cleaning the motor and Motor mount bolt stuck

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Cleaning the motor and Motor mount bolt stuck

    Good morning Gents. I'm trying to clean a motor on a 1978 GS750 i scored recently. This thing Is being a pain. I've got most of the grease off but the impurity's in the fins are driving me crazy. Anyone have any tricks and tips to smooth the metal and have it look somewhat new? I'm at the point of attaching a wire wheel to a drill and going to town.

    Second during removal i have the front upper motor mount stuck with one of the bracket still on the motor. This bugger is stuck and not moving. I've been spraying PB blaster on it for 3 days with no success what so ever. Options?

    #2
    See my thread here. Use some Hemostats and patches fo the dish scrubbie to get in and scrub the oxidation away. Then degrease again to remove the oil.

    MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
    1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

    NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


    I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

    Comment


      #3
      This is the end result after doing the Marvels treatment, degreasing and power washing, and repainting the engine for my 77 KZ 650B1 project.









      MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
      1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

      NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


      I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

      Comment


        #4
        Oh wow! Good work man. I'd post pictures but Photobucket is down. I've got a good amount of the gunk off but the oxidation on the bottom and the fins is not budging. I will give this a try. This bike sat for 5 years and was clearly neglected. My buddy said you can't turn a whore into a house wife so this whole project is to prove him wrong. For $250 purchase price i had it running the first day. I'm only a week into the rebuild with the bike stripped and almost ready for the powder coater.

        Comment


          #5
          A rifle cleaning brush chucked in a drill cleans the fins, but be careful and use low RPM, if you bend the brush at all as it turns it will break off. Might be better to use it in your hand with just an in and out motion.
          http://img.photobucket.com/albums/v5...tatesMap-1.jpg

          Life is too short to ride an L.

          Comment


            #6
            Small screw drivers to chip the thick hard chain lube and crud off before the scrubbing speeds it up considerably.
            MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
            1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

            NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


            I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

            Comment


              #7
              To clean the fins I used a scotchbrite pad wrapped around a paint stick. To get into the little crevices I whittled the paint stick down a bit. You can use different grits of pads depending on how bad the tarnish is. It took about 4 hours to do the entire engine the first time. Every year I go over it again quickly with a fine pad to keep it looking clean. Patience is the key here. I have not used Marvel's or POR as they are not available locally but I hear they are good products.

              Comment

              Working...
              X