Announcement

Collapse
No announcement yet.

03 GSXR-1000 USD forks good for the swap?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    03 GSXR-1000 USD forks good for the swap?

    I have a chance to get a set of 03 GSXR-1000 K3 USD forks and trees for $200 plus a little extra for the calipers..

    Are these good ones to use on a GS1000 or are they going to be really short?

    I know I'll need the 30x47 conversion bearing to mount them up.

    #2
    I run the 04 Gixxer 1000 forks on my bike. They're really short. With a twinshock rear setup, you're gonna low riding and dragging your header. Have you considered either longer forks or doing a monoshock conversion in the rear?

    Comment


      #3
      Can you get "extension" caps for those ones? There are a couple of places that make them now.
      Basically an extended top cap that allows you to push the forks through another inch or two & bolt the triple around the new cap instead of around the fork leg.

      The Stepped Honda triples would buy you an inch too...
      1980 GS1000G - Sold
      1978 GS1000E - Finished!
      1980 GS550E - Fixed & given to a friend
      1983 GS750ES Special - Sold
      2009 KLR 650 - Sold - gone to TX!
      1982 GS1100G - Rebuilt and finished. - Sold
      2009 TE610 - Dual Sporting around dreaming of Dakar..... - FOR SALE!

      www.parasiticsanalytics.com

      TWINPOT BRAKE UPGRADE LINKY: http://www.thegsresources.com/_forum...e-on-78-Skunk/

      Comment


        #4
        Yeah that what I'm finding.Something like 725mm vs 775 for the 1000 USD's. Guess I'll hold out till I can get a set of GSXR1100 forks.

        I have the parts to do a mono shock but I don't want to make any permanent alterations to my 78.. I'd do it to my 79 L but I'm not sure I'll keep it around after I finish the 78 E

        Thanks!

        Comment


          #5
          I modified a GS 1000 to take GSX R 1100 K ( 89) suspension and wheels.
          The bike is a delight to ride but...the ground clearance could be an issue on a track as I have less than 45° static lean angle.
          FYI, here's the length of the different forks you can use for such a project:
          GSX R K : 740 mm
          GSX R G/H: 765 mm
          Bandit : 780 mm
          GS 1000 original : 775 mm
          GS 1100 Katana: 850 mm.
          I believe the best choices are eitheir GSX R K yokes with bandit tubes ( 43 mm) or GSX R G/H complete fork (41 mm).
          The GSX R G/H combination will require the use of the original 18" front wheels which is good for ground clearance but requires expensive replacement disk brakes.
          I believe this is the setup used by Posplayer?
          On my GS 1000 XP as I have the GSX R K setup, I will eitheir use a custom stepped top yoke or an 18" front wheel from the rare GSX R 1100 J model.
          Here's the bike in it's current definition:
          sigpicJohn Kat
          My bikes: CB 77, GS 1000 ST Cafe Racer with GSXR 1052 engine, GS 1000 ST, XR 41 Replica with GS 1085 engine,
          GS 1100 SZ Katana with GS 1135 EFF engine, KTM Superduke 1290 R 2020

          Comment

          Working...
          X