Announcement

Collapse
No announcement yet.

Can't remove damper rod

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Can't remove damper rod

    I would rather not purchase a special tool to dismantle my forks. Trying the dowl method. I did so in '92 but now it is not working. Does anyone understand the mechanism enough to tell me how to break the nut loose? The dowel is secured but spins after enough torque on the nut. Need to have my bike on the road ASAP. Please help...

    #2
    I can understand not wanting to spend a lot of money for a special tool, but are you also against spending about $6 to make one?

    Get a piece of 1/2" all-thread rod that is two feet long, and four nuts. Put two nuts at one end, jam them together,
    do the same thing at the other end, but leave about 3/4" of rod sticking out. (You can make both ends the same, to make it easier.)




    Put your new tool down the fork leg, you will feel the nut fit into the top of the damper rod and hold it in place.
    Put a wrench on the inner nut at the top to hold the tool, remove the screw on the bottom of the fork.

    .
    sigpic
    mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
    hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
    #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
    #2 son: 1980 GS1000G
    Family Portrait
    Siblings and Spouses
    Mom's first ride
    Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
    (Click on my username in the upper-left corner for e-mail info.)

    Comment


      #3
      If you use an impact wrench then it doesn't take much force at all on the inside nut to spin out the bolt.

      I have a long piece of copper pipe that fits nicely down the center of my 88 GSXR forks and provides just enough friction.

      Comment


        #4
        I keep the spring in and use an impact.
        1983 GS 1100E w/ 1230 kit, .340 lift Web Cams, Ape heavy duty valve springs, 83 1100 head with 1.5mm oversized SS intake valves, 1150 crank, Vance and Hines 1150 SuperHub, Star Racing high volume oil pump gears, 36mm carebs Dynojet stage 3 jet kit, Posplayr's SSPB, Progressive rear shocks and fork springs, Dyna 2000, Dynatek green coils and Vance & Hines 4-1 exhaust.
        1985 GS1150ES stock with 85 Red E bodywork.

        Comment


          #5
          Originally posted by chef1366 View Post
          I keep the spring in and use an impact.
          Same here.

          Take the screw out of the bottom before taking the rest of it apart (but after draining it). Invert the fork leg and grip it with your feet. With your left hand, hold it against your right thigh. Make sure of the direction the rattle gun will turn. Make sure the bit is well seated in the screw's socket. Put your weight on the fork leg to compress it and pull the trigger.

          Reassembly is the same, but turning the other way and with some blue loc-tite applied. Granted, with this method you're sort of spit-balling the torque.
          Dogma
          --
          O LORD, be gracious to me; heal me, for I have sinned against you! - David

          Skeptical scrutiny is the means, in both science and religion, by which deep insights can be winnowed from deep nonsense. - Carl Sagan

          --
          '80 GS850 GLT
          '80 GS1000 GT
          '01 ZRX1200R

          How to get a "What's New" feed without the Vortex, and without permanently quitting the Vortex

          Comment


            #6
            You guys rock! I did see the earlier post of the all thread tool and for some reason it didn't click. But I get it now, the exposed nuts are to get a wrench on. I also thought of an impact right before I posted but couldn't find the right size. I'm on the right track. Thank you for your help.

            Comment


              #7
              By the way, Steve. That is the weirdest looking tape measure I have ever seen. 8-)

              Comment


                #8
                Originally posted by bluehwy View Post
                By the way, Steve. That is the weirdest looking tape measure I have ever seen. 8-)
                It probably dates him.
                1983 GS 1100E w/ 1230 kit, .340 lift Web Cams, Ape heavy duty valve springs, 83 1100 head with 1.5mm oversized SS intake valves, 1150 crank, Vance and Hines 1150 SuperHub, Star Racing high volume oil pump gears, 36mm carebs Dynojet stage 3 jet kit, Posplayr's SSPB, Progressive rear shocks and fork springs, Dyna 2000, Dynatek green coils and Vance & Hines 4-1 exhaust.
                1985 GS1150ES stock with 85 Red E bodywork.

                Comment


                  #9
                  19MM bolt welded into some conduit. Make the long leg at least 22 inches.Once the bolt head locks in to the dampner rod, simply flip it over and stand on the handles and you can use both hands to remove the allen head bolt. May help to heat the bolt a bit in case it has been loctited in. Be sure to REPLACE the crush washers that seal the fork and bolt.



                  MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
                  1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

                  NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


                  I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

                  Comment


                    #10
                    Originally posted by bluehwy View Post
                    By the way, Steve. That is the weirdest looking tape measure I have ever seen. 8-)
                    Is that one of those folding rulers? A 6' ruler that folds up in 6" segments and kind of looks like a brick when its all folded up? Yeah, my grandpa had one of those.....

                    Comment


                      #11
                      Your bike is different than a 650, but a broom handle works on the 650. Might be worth a try for free before you go spend money.

                      Comment


                        #12
                        Originally posted by bluehwy View Post
                        By the way, Steve. That is the weirdest looking tape measure I have ever seen. 8-)
                        Maybe because it's not tape?

                        Originally posted by chef1366 View Post
                        It probably dates him.
                        No, it was never that kind of relationship.

                        Originally posted by Homie View Post
                        Is that one of those folding rulers? A 6' ruler that folds up in 6" segments and kind of looks like a brick when its all folded up? Yeah, my grandpa had one of those.....
                        Yep, that's it.

                        I used that ruler when I was working in construction over 40 years ago.

                        .
                        sigpic
                        mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
                        hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
                        #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
                        #2 son: 1980 GS1000G
                        Family Portrait
                        Siblings and Spouses
                        Mom's first ride
                        Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
                        (Click on my username in the upper-left corner for e-mail info.)

                        Comment


                          #13
                          I welded a 19mm bolt head to a length of 1/2 inch round stock and then welded an old socket the other end so I can put a ratchet on it to make life easier. Over thought but I like to weld.

                          Comment


                            #14
                            Originally posted by JATO View Post
                            I welded a 19mm bolt head to a length of 1/2 inch round stock and then welded an old socket the other end so I can put a ratchet on it to make life easier. Over thought but I like to weld.
                            Works GREAT, if you have a welder.

                            Another option that has been suggested in the past is to take a spark plug socket that has a hex on the end, turn it backwards and put it on a VERY LONG extension, then stick it down the fork tube. The concept is pretty much the same as your creation, but without the welding.

                            .
                            sigpic
                            mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
                            hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
                            #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
                            #2 son: 1980 GS1000G
                            Family Portrait
                            Siblings and Spouses
                            Mom's first ride
                            Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
                            (Click on my username in the upper-left corner for e-mail info.)

                            Comment

                            Working...
                            X