Announcement

Collapse
No announcement yet.

spoked GS 1000 Wheels on a '79 GS 550

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    spoked GS 1000 Wheels on a '79 GS 550

    Hey everyone

    I just happened upon a (1979?) GS 1000 parts bike (no motor) with the spoked wheels on it. It was cheap, so I bought it on the off chance that some of the parts could be transferrable to my '79 GS550. I've read elsewhere that these wheels are desirable and apparently difficult to come by. Not sure if that's accurate or not but I like the look of the wheels, and was thinking if it is possible i'd swap them over to my 550 which currently has the typical "star" pattern wheels.

    My guess is that there are a couple of ways I could do this. Please correct me if I'm wrong here.

    1. pull the wheels off and swap out the necessary bearings/bushings/washers etc. to make it fit with my forks/brakes/axles/sprocket

    2. pull the entire front end off the parts bike and change out the stem bearings to make it work, and change necessary bearings/parts to make rear wheel work

    the forks from the 1000 looked to be in pretty good shape, although I haven't had a chance to really dig in to things... I'm pretty sure the brakes from the 1000 looked quite questionable

    Would using the front end from a 1000 have any adverse affects? obviously they would be designed for a heavier bike, so is that dodgy territory to be messing around in, or not such a big deal? I haven't taken any measurements yet to see if the fork lengths are vastly different, but if the front ends vary too significantly that would obviously be cause for concern.

    anyone have any preliminary advice for me right off the hop here. I haven't torn anything apart yet, or taken any measurements, so I really have no clue what will fit and what will not as of yet. Just figured someone here may have already done this and could save me some head scratching.

    Thanks!

    #2
    Just swap wheel bearings for the larger axles and be done with it. Have you got the rear disc brake already? If not the swing arm and other parts from a 550L will work.
    http://img.photobucket.com/albums/v5...tatesMap-1.jpg

    Life is too short to ride an L.

    Comment


      #3
      Yes they fit, I put a set of GS750 spoked wheels on a 78 GS550 just change the bearings in the rear and your good to go. 1000 wheels are the same fittings.
      My bikes 79 GS1000 1085 checked and approved by stator the GSR mascot :eagerness: and 77 GS750 with 850 top end, GS850g, and my eldest sons 78 GS550, youngest sons GS125. Project bike 79 GS1000N

      Comment


        #4
        Did the 550s in England come with a disc brake on the rear?
        http://img.photobucket.com/albums/v5...tatesMap-1.jpg

        Life is too short to ride an L.

        Comment


          #5
          Thanks everyone for your input!

          Rear discs on both the parts parts bike, and my 550, so it should all work out just right. I'll be swapping out the bearings as suggested as soon as I get a bit of time to get working on it.

          Comment


            #6
            Originally posted by tkent02 View Post
            Did the 550s in England come with a disc brake on the rear?
            The first ones were drum rear but the later ones had discs.
            79 GS1000S
            79 GS1000S (another one)
            80 GSX750
            80 GS550
            80 CB650 cafe racer
            75 PC50 - the one with OHV and pedals...
            75 TS100 - being ridden (suicidally) by my father

            Comment

            Working...
            X