Announcement
Collapse
No announcement yet.
tube or tubeless tyres for 1980 Suzuki's?
Collapse
X
-
Originally posted by Rich82GS750TZ View PostBob T. ~~ Play the GSR weekly photo game: Pic of Week Game
'83 GS1100E ~ '24 Triumph Speed 400 ~ '01 TRIUMPH TT600 ~ '67 HONDA CUB
-
Forum GuruPast Site Supporter
Super Site Supporter- Jun 2018
- 5525
- Mifflinburg, PA / Land of Tar & Chip
Originally posted by Baatfam View PostI notice you don't get a lock nut with the Amazon one...
Funny, the more I try to do as much of this from home as possible, the more likely I seem to be to have to go to some store anyway. The good hardware store with the good loose hardware selection in my town is in the same plaza as NAPA.Rich
1982 GS 750TZ
2015 Triumph Tiger 1200
BikeCliff's / Charging System Sorted / Posting Pics
Destroy-Rebuild 750T/ Destroy-Rebuild part deux
Comment
-
Originally posted by Rich82GS750TZ View PostLooks like you're right. I can just pick up another nut same size as other, right? nothing special about it?
Funny, the more I try to do as much of this from home as possible, the more likely I seem to be to have to go to some store anyway. The good hardware store with the good loose hardware selection in my town is in the same plaza as NAPA.Bob T. ~~ Play the GSR weekly photo game: Pic of Week Game
'83 GS1100E ~ '24 Triumph Speed 400 ~ '01 TRIUMPH TT600 ~ '67 HONDA CUB
Comment
-
Forum GuruPast Site Supporter
Super Site Supporter- Jun 2018
- 5525
- Mifflinburg, PA / Land of Tar & Chip
Originally posted by Baatfam View PostThe nut on the old tube should/might be the same.
Funnily enough, the picture with on the NAPA site for valve 90-426 is the same picture used on the Amazon listing I bought, showing only one nut. Will see what comes from Amazon - (tomorrow, maybe?)
Rich
1982 GS 750TZ
2015 Triumph Tiger 1200
BikeCliff's / Charging System Sorted / Posting Pics
Destroy-Rebuild 750T/ Destroy-Rebuild part deux
Comment
-
Originally posted by Rich82GS750TZ View PostBrilliant.
Funnily enough, the picture with on the NAPA site for valve 90-426 is the same picture used on the Amazon listing I bought, showing only one nut. Will see what comes from Amazon - (tomorrow, maybe?)
Bob T. ~~ Play the GSR weekly photo game: Pic of Week Game
'83 GS1100E ~ '24 Triumph Speed 400 ~ '01 TRIUMPH TT600 ~ '67 HONDA CUB
Comment
-
Forum GuruPast Site Supporter
Super Site Supporter- Jun 2018
- 5525
- Mifflinburg, PA / Land of Tar & Chip
Jules,
I apologize if I've hijacked your thread with my own issue, but it is all related to your initial post, I think. And I believe a lot of good info has been presented here that will hopefully help some in the future.
Best.Rich
1982 GS 750TZ
2015 Triumph Tiger 1200
BikeCliff's / Charging System Sorted / Posting Pics
Destroy-Rebuild 750T/ Destroy-Rebuild part deux
Comment
-
Forum GuruPast Site Supporter
Super Site Supporter- Jun 2018
- 5525
- Mifflinburg, PA / Land of Tar & Chip
Got my tire remounted today onto my freshly de-corroded wheel. The valve I bought fit perfectly, only came with one nut, so I used the one from the old tube for a lock nut. The tire installation was more difficult than I thought it would be. I had the tire’s beads squeezed all around with giant zip ties as suggested by some videos. I think this actually hurt me rather than helped. As toward the end (of me swearing and sweating with the tire 3/4 of the way on), only after the last two zip ties broke, allowing one bead, then the other to slip over the rim, was I able to finally get it on. Maybe the zip tie thing works for some tires/wheels. Didn’t work for me. Found a set of 3 rim protectors and a Gallon of lube on Amazon for cheap, worth every penny. I also could not have gotten this done without the 24” tire iron I picked up at HF to supplement the 2-10” irons I already had.
Anyway, it’s on. I did not get the satisfying pops of the beads seating on filling with air. Even filled it to 7O psi. Then reinstalled the valve in the stem and settle it to about 50. I’ll check in another hour before mounting back on the bike, then reset to running psi. Just to check, wiping the bead area with more lube yielded no bubbles, so that’s good. If no pops, are the beads really seated? I did use an actual tire lube/bead sealer.
Last edited by Rich82GS750TZ; 12-23-2020, 02:09 PM.Rich
1982 GS 750TZ
2015 Triumph Tiger 1200
BikeCliff's / Charging System Sorted / Posting Pics
Destroy-Rebuild 750T/ Destroy-Rebuild part deux
Comment
-
Nice! Good to see....Bob T. ~~ Play the GSR weekly photo game: Pic of Week Game
'83 GS1100E ~ '24 Triumph Speed 400 ~ '01 TRIUMPH TT600 ~ '67 HONDA CUB
Comment
-
Forum LongTimerBard Award Winner
GSResource Superstar
Past Site Supporter
Super Site Supporter- Oct 2003
- 17439
- Indianapolis
No, the beads don't usually "pop" when the bead seats on conversions. They just sort of ooze into place.
Weird about the number of nuts -- the Napa valve stems in my stash with the same part number look identical, but they have two nuts plus that domed washer. I just installed a couple a few weeks ago.I used a thin wrench to hold one and torque the other a bit, and applied a drop of Loctite green (low strength wicking) thread locker for that cozy belt and suspenders feeling.1983 GS850G, Cosmos Blue.
2005 KLR685, Aztec Pink - Turd II.3, the ReReReTurdening
2015 Yamaha FJ-09, Magma Red Power Corrupts...
Eat more venison.
Please provide details. The GSR Hive Mind is nearly omniscient, but not yet clairvoyant.
Celeriter equita, converteque saepe.
SUPPORT THIS SITE! DONATE TODAY!
Co-host of "The Riding Obsession" sport-touring motorcycling podcast at tro.bike!
Comment
-
It seems I need some humble pie .... as only now in my
dumb a%s ignorance do I realise I need to
make this conversion happen and by a valve .....
So its tyre off.
check rim. (read this thread)
drill rim with one of those drill bits
buy one of them valves
and new tubeless tyre .....UKJULES
---------------------------------
Owner of following bikes:
1980 Suzuki GS550ET
1977 Yamaha RD 250D
1982 Kawasaki GPZ 750 R1
1980 Suzuki GSX 250E
Comment
-
A nice pie that was.
Front wheel off asap (by dealer )for new tubeless avon road rider.
I need to convert rim !!!!!!!
1) remove tyre and take pic of rim (for my own benefit but will post)
2) need m8*16mm counterbore drill bit to convert valve hole.
q) this I assume to expand original hole and make nice
flat area for valve seat to not leak.
q) I am in uk. can any expert with time on his hands
find the drill bit on ebay or amazon - as can get that next day ?
I cant quite get which one to use ?
q) when got the drill bit it is just a simple matter
of drilling out hole a bit (to 8/8.35mm) and making a flat area on
inside of rim (16mm ish)
A 1/4 slice of the humble pie to anyone ....... who can help.Last edited by ukjules; 01-14-2021, 04:33 PM.UKJULES
---------------------------------
Owner of following bikes:
1980 Suzuki GS550ET
1977 Yamaha RD 250D
1982 Kawasaki GPZ 750 R1
1980 Suzuki GSX 250E
Comment
-
UKJULES
---------------------------------
Owner of following bikes:
1980 Suzuki GS550ET
1977 Yamaha RD 250D
1982 Kawasaki GPZ 750 R1
1980 Suzuki GSX 250E
Comment
-
Arghhh I'll stick a tube in it as it is meant to be.
Too much hassle p^%$&ng about.
My only concern was due to the massive
rides I do around europe ..... if I didnt
do this I would even think of this as a question
worth asking.
I'll carry tube sealant spray and
rely on the AA (break down people).
avon road rider with tube it is.UKJULES
---------------------------------
Owner of following bikes:
1980 Suzuki GS550ET
1977 Yamaha RD 250D
1982 Kawasaki GPZ 750 R1
1980 Suzuki GSX 250E
Comment
Comment