Again, no expert, but I don’t understand why all the grounding points.
-
Required reading for all forum users!!!
Welcome!
Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.A note to new registrants...
All new forum registrations must be activated via email before you have full access to the forum.A Special Note about Email accounts!
DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.A note to old forum members...
I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.
Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...
-
Returning Visitors
If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.
If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.
Suzuki GR (almost GS) 2 cyl Tempter is charging low .. and coil question
- Thread starter dennco2
- Start date
dennco2
Forum Mentor
I was trying to connect the sh775 ground lead to the ground wire in the wiring harness AND try to create a super robust grounding point with the grounding cable .... and hopefully lower my system ohms and raise system voltage. My replacement add on wires are only 16 gauge, so I was trying to keep them short in length .... and carry the current the rest of the way using way larger cable. If you see a flaw in my logic ... let me know.
Again, I’m not an expert in this. And it’s highly likely I am wrong. Just seems to me you should be looking at creating fewer, not more ground mounting point at which your harness grounds, RR ground, engine ground come together.
I’m not suggesting at all that you wire yours like mine. But mine works, wiring the RR- directly to batt - will also work. From your description, I gathered that you are collecting grounds at more than one place, hence not a SINGLE Point Ground. Maybe I misunderstood this statement and photo:
”The green wire goes straight to the neg side battery. The black ground wire goes to the grounding point to the new sh775 with 3 ring connectors.
”
”The green wire goes straight to the neg side battery. The black ground wire goes to the grounding point to the new sh775 with 3 ring connectors.
dennco2
Forum Mentor
I?m not suggesting at all that you wire yours like mine. But mine works, wiring the RR- directly to batt - will also work. From your description, I gathered that you are collecting grounds at more than one place, hence not a SINGLE Point Ground. Maybe I misunderstood this statement and photo:
?The green wire goes straight to the neg side battery. The black ground wire goes to the grounding point to the new sh775 with 3 ring connectors.
Okay, I have redirected the large ground cable from the 3 ring connectors ..... straight to the neg battery terminal and stacked it on top of the engine/frame ground. Definitely more direct to the battery that way and probably lowers the volt drop between connections. I'm about to put the fuel tank back on and see what happens. An update later.
dennco2
Forum Mentor
The update with my Suzuki GR650 Tempter twin cyl. .... with like new Shindengen SH775 reg/rec just installed today.
Not sure how valid my volt numbers are because I have not got my tach working as yet ... and the multi-meter battery just crapped out.
Before it did I got:
Key off: 12.62 Bike and battery has been sitting for weeks
Key on: 12.12
Idle: 14.19
2,000 to 4,000 rpms had to be approximated ... but the volts never got over 14.30
Key off: 13.17
This is the 1st time I have seen 14+ volts showing on the meter! I'll test it again later with a new battery in the meter. I am surprised the volts shot up to 14 at idle!
With the tank off I checked the air/fuel mixture screws. One was out 2.5 turns and the other was out about 5 turns from bottoming out. I adjust both to 2.5 turns out and had to run full choke till the engine slowly warmed up. I might have to reach in and raise the idle adjustments now ... too low idle speed. More to do, but I'm looking forward to longer rides without worrying about running the battery down!!
Not sure how valid my volt numbers are because I have not got my tach working as yet ... and the multi-meter battery just crapped out.
Before it did I got:
Key off: 12.62 Bike and battery has been sitting for weeks
Key on: 12.12
Idle: 14.19
2,000 to 4,000 rpms had to be approximated ... but the volts never got over 14.30
Key off: 13.17
This is the 1st time I have seen 14+ volts showing on the meter! I'll test it again later with a new battery in the meter. I am surprised the volts shot up to 14 at idle!
With the tank off I checked the air/fuel mixture screws. One was out 2.5 turns and the other was out about 5 turns from bottoming out. I adjust both to 2.5 turns out and had to run full choke till the engine slowly warmed up. I might have to reach in and raise the idle adjustments now ... too low idle speed. More to do, but I'm looking forward to longer rides without worrying about running the battery down!!
dennco2
Forum Mentor
Very happy with the Shindenden R/R. Excellent upgrade part for a 38 year old Suzuki and it saved the day for me. Thanks to all who really did help me get to this point on the restoration. More to do but I just took a 30 minute ride and the battery shows 12.95 volts 10 minutes after I got home. Now I have to improve the idle and get the tach working.
Isn’t it like you’ve successfully performed a difficult magic act when you finally see the VM read over 14 volts?! Well done dennco2.!
Now, what do you know, if anything, about the valve clearances on this bike. Did you do them, or know for a fact that they are in spec? If not, I’d suggest that as a next step before messing with carbs.
Now, what do you know, if anything, about the valve clearances on this bike. Did you do them, or know for a fact that they are in spec? If not, I’d suggest that as a next step before messing with carbs.
Last edited:
dennco2
Forum Mentor
Isn?t it like you?ve successfully performed a difficult magic act when you finally see the VM read over 14 volts?! Well done dennco2.!
Now, what do you know, if anything, about the valve clearances on this bike. Did you do them, or know for a fact that they are in spec? If not, I?d suggest that as a next step before messing with carbs.
I have shims left over from adjusting the valves 2 years ago on my GS450. I had to go thru a 100% learning curve with the shims, and best methods. I have forgotten a lot. The Tempter backfires a bit sometimes. Yes I am sure that needs attention ... asap. I will have to find that info in this forum and go thru it again.
dennco2
Forum Mentor
Isn?t it like you?ve successfully performed a difficult magic act when you finally see the VM read over 14 volts?! Well done dennco2.!
Now, what do you know, if anything, about the valve clearances on this bike. Did you do them, or know for a fact that they are in spec? If not, I?d suggest that as a next step before messing with carbs.
The 4 valves are now adjusted within specs. One exhaust had near zero clearance and was hurting performance. Hopefully the valve is still good ... and I think it is because the power and acceleration is pretty invigorating now. I got back from a spirited run and checked the battery voltage .... 12.95. More heat coming off the engine and pipes than ever before .. hope it not running too lean.
That should give you more smooth running dennco,even when it gets stuck in traffic and heats-up.How does your spark plug color look,possibly running a little lean?