• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

1981 gs-550t

  • Thread starter Thread starter doggies
  • Start date Start date
D

doggies

Guest
This seems strange has anyone encountered this before. I have the bike running on three cylinders only. At an idle I am getting spark on cylinder 1-2-3-4 when I increase idle or throttle up the bike at all I loose spark at number three cylinder. The bike has a 4into 1 header which was on it when purchased. I relaced the fuel petcock because the rubber check was mush. New fuel and vacuum lines. New plugs. I have jumped this bike numerous times and had charged the battery. Battery is putting out about 13.4 volts with lights on. Any help would be great. I know one of the ign. coils was changed because it says good painted on it. That's about it. I did not disassemble the carbs.
 
Hi,

I've got one thought. How about new plug caps?


Now I'll have to find another thought somewhere. :p




Thank you for your indulgence,

BassCliff
 
Hey Bill, you're a little quicker with the clicker tonight. I thought you might go deeper though. I'm still learning about these here motorsickle things. :p

Hey Mr. doggies, keep us informed.


Thank you for your indulgence,

BassCliff
 
Both coils are firing so that means the crank trigger works as is the igniter.
Puts it on the wires or spark plug caps.
Deep enough? :p
 
How can it lose spark on 3 when 2 works fine? If this is the correct info then the HT lead or cap leading to 3 is broken.
My 550 always started on 3 cylinders and took an age to warm number 4 up.
I listened to the experts on this site then I checked and adjusted the valve clearances and cleaned the carbs.
Bike starts and runs like a dream now.
 
Unless all the maintenance work on the bike is up to snuff like waltfen says, the bike will continue to run poorly for one reason or another.

You need to build a baseline by doing basic work: rebuild the carbs with fresh O-rings inside the carbs and on the intake boots, adjust the valves, clean the air filter, change the plugs, check the charging system (use the stator papers), etc.

After this work is done, you can hone in on problems much easier since you know what the problem can't be.

Don't do maintenance work and wait til the bike breaks down, and it will, and you are just guessing at what the problem will be.

Good luck.
 
plug caps. and you said it came with a header. was it properly rejetted?
 
No Spark

No Spark

What I did was pull #3 plug and hold it against the head while it was running. Today I switched caps after trying to start it. I cut some plug wire off and re attached. The plug got spark but I noticed they are always carbon black and they are fresh plugs stock heat range. I clean them off with my plug blaster but they get black again. Now when I got the bike it had a header 4into 1 on it would this make a differance if the carbs were not rejetted. I really don't want to go through all that. The bike sounds good with it and is quick as well when firing on all four. Open for suggestions. Have no touched the carbs. at all.
 
doggies said:
What I did was pull #3 plug and hold it against the head while it was running. Today I switched caps after trying to start it. I cut some plug wire off and re attached. The plug got spark but I noticed they are always carbon black and they are fresh plugs stock heat range. I clean them off with my plug blaster but they get black again. Now when I got the bike it had a header 4into 1 on it would this make a differance if the carbs were not rejetted. I really don't want to go through all that. The bike sounds good with it and is quick as well when firing on all four. Open for suggestions. Have no touched the carbs. at all.
Click to expand...

You HAVE to go through the carbs, or you'll likely never get it running right. There are no shortcuts. There is a step by step, logical procedure for getting these old bikes running good as new. If you don't want to bother with "all that", sell it and get something newer.
 
Carb. rebuild

Carb. rebuild

Got spark on all 4 where is the best place to get carb. parts for an 81' GS550:)
 
doggies said:
Got spark on all 4 where is the best place to get carb. parts for an 81' GS550:)
Click to expand...

Now yer talkin'....

Actually, you probably won't need any parts for the carbs other than o-rings. You'll just need to completely dismantle them, thoroughly dip and clean them, then correctly reassemble them with a new o-ring set from Robert Barr. http://www.cycleorings.com/

There is an excellent tutorial linked from the main page of this site that walks you through it step by step.
 
You must log in or register to reply here.

Similar threads

P
Hanging Idle/Pilot Air Screws
Replies
2
Views
57
Nessism
Nessism
MiahSlays6332
82 650L #2 Cyl Inop (Can’t find answer)
Replies
6
Views
159
chuck hahn
chuck hahn
B
1982 Suzuki GS850L Project Bike
Replies
2
Views
70
rphillips
R
J
GS850 revs to 4500~ then pops
Replies
3
Views
106
Nessism
Nessism
L
Hanging Idle (I know, but bear with me) and different carbs
2
Replies
20
Views
430
dgates1
dgates1
Back
Top