• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

82 GS850GL Compression

  • Thread starter Thread starter Harry P.
  • Start date Start date
H

Harry P.

Guest
Did a compression test #1=80, #2=105, #3=105 #4=109...#1 is below the service limit of 100 according to the manual.

How bad is it to run it like this?

What is involved getting #1's numbers up? If I do 1 I guess I'll do them all.

Please advise...thanks guys.
 
A couple of things to check before the wrenches fly:

1. Did you hold the throttle open for all the readings?

2. Were the readings taken cold or warm?

3. Were the readings taken dry or wet?

4. Have you adjusted the valves?



1. If you don't hold the throttle open, the cylinder will have a hard time inhaling air to compress.

2. Readings are usually better when warm because all the parts are expanded to proper clearances.

3. If the readings were 'dry', add a teaspoon or so of oil to each cylinder and try it again. If the readings go up dramatically, you have bad seals on the rings, and the oil just helped seal them. If the readings did not go up very much, you likely have problems with the valves.

4. If the valves are too tight, pressure might be leaking out past the tight valve, giving you a low reading. Make sure the valve adjustment is proper and try again.

.
 
Need more input please.
How many miles on the bike? Has it been sitting any length of time or been used continuously? Does it use oil? Any leaks?

Low compression could be as a result of bad valves or piston rings or both but in order to determine which you would need to use a leak-down tester to be sure(available from auto parts stores or Harbour Freight but you need a compressor to attach it to) . If you pour in a little oil and re check does the compression go up? If so its rings.

Low compression in one cylinder is not going to cause a lot of grief so i wouldn't get too worried unless its accompanied by banging and clanging. Ride the snot out of it and if you feel up to it in the down season rip into it.

Good luck.
Cheers,
Spyug
 
Harry Porosky said:
How bad is it to run it like this?
Won't make it any worse, maybe just run like crap, maybe a rough idle.

What is involved getting #1's numbers up?
Has the bike sat a long time?
Most likely, adjust the valves, and go ride it for a while.

Please advise...thanks guys.
Click to expand...
Post a little more info, history, maintenance, etc.
 
Looks like I jumped the gun on the test...

Have not adjusted the valves, carbs and airbox are off, engine is cold, have changed the oil and turned it over a dozen or so times thinking this was sufficient to get oil where it needed to be.

Bike is new to me with 70,000 miles, not sure of PO maintenance, wasn't running when I got her..cleaned the carbs, replaced O rings, adjusted the floats, she fired up and sounded strong...but bogs down when she gets hot.

I'll do the valve clearance check tomorrow night, get it in spec, replace the carbs & airbox...run her for a bit off a temp tank to warm her up and see where I am then. If this isn't right let me know.

I am a noob...please be gentle. Thanks.
 
Last edited:
Harry Porosky said:
If this isn't right let me know.
Click to expand...

Probably will help a lot, probably get your test numbers in spec, but several hours of running may be needed to get the compression test numbers up to where they should really be, especially if it has sat unused a long time.
70,000 miles is nothing for an 850 given proper maintenance, and if it has not been overheated, run too lean, run with valves too tight, or with any of a number of other problems having been neglected...
 
Please, please, PLEASE check the valve clearances.
 
You must log in or register to reply here.
Back
Top