• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Blinker not Blinking

  • Thread starter Thread starter robinsoncr
  • Start date Start date
R

robinsoncr

Guest
Ok, I have a front left turn signal issue here.

When I bought the bike, the right signals worked correctly. The left would burn an not blink, the left front wouldn't burn or blink.

I replaced the bulb in the front left. Now, it both left front/rear will burn but neither will blink. When you select the left turn signal, you can hear a click as though it wants to blink but doesn't. Any ideas?

Thanks,
Chris
 
Bad earth, broken wire.....

Suzuki mad

GS1000ET
GS(X)1100ESD
GSF1200K1
 
Had same problem after the GS1000 had been into the main dealer. During strip down the earrth wire had snapped and the mechanic had stuck a bit of rubber glove over the broken wire and shoved it back into the indicator.

I also had the same problem after refitting the tank. Follow the left hand indicator wire down to where it joins the main loom and check the block connector as they can sometimes come loose there.

You can also clean the contacts with the bulb as it will sometimes do it.

Suzuki mad

1981 GS1000ET
1983 GS(X)1100ESD
2002GSF1200K1
 
You did not say what type of GS it is, but I had to replace the turn signal control unit on my GS1100E. Works like a charm now.
 
Update:
Ok, I took my trusty multimeter and started checking continuity. I took the headlight out and found the left and right blinker wire harnesses.

I found that the right signal's secondary circuit (blinking) is a white wire from the stalk to a 1to1 connector to a lime green wire coming out of the harness. Ground is black w/white stripe and is connected via a 1to1 connector to a black w/white stripe that goes into the harness. Checked it for continuity when turned on. Works fine.

Tracing the left signals wires, I found that the ground, black w/white strip is connected to a 2to1 connector. White wire (blink hot) is connected to the same 2to1 connector as the ground! I can't find a free connector that would run from the battery as a hot to the white from the stalk.

I double checked the circuit from the bulb back by swapping the supply from left to right. So, when I turned on the right (working) blinker, it made the left hand (non-working) bulb flash. So, I know it should function.

Does anyone have a wiring diagram that would tell me what the wire should look like that supplys the secondary (flasher) circuit from the main harness to the stalk's harness?

Thanks,
Chris
 
Nevermind. I typed this message and then walked back out to the bike and found the errant lead! Next time, I'll go pretend to type a post and then walk back and look again before actually posting!

Thanks,

Chris
 
Glad you found the problem... one of the mounts for my indicators is bent a bit, and every now and then i think it shorts out a bit on the fender causing my lights not to blink...
 
The fact that you see both bulbs lighting when you select a turn indicates that there's nothing wrong with any of the wiring or bulbs of course and that your signal switch is selecting ok. The 2 most likely causes of your problem based on the above are.......a bad flasher.....this can be replaced with a typical 2 prong automotive unit......and secondly, low system voltage (you'd notice the bulbs being dim......and have other issues such as poor cranking.....running maybe).

On my GS1000 the flasher is on the left side under the cover.
 
You must log in or register to reply here.
Back
Top