• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Boiling carbs ? :)

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
I remember back in the day when I was little, I found in a book that you could boil vinegar and put pennies in it, and they would come amazingly clean. I'm wondering if anyone has tried this with actual motorcycle parts, esp, carbs. It seems all the small passages, all the jets, and the carb its self, would benefit greatly from a good boiling clean. Im not sure what type of chemical to use? Im guessing vinegar, but there are many others.

Anyone try this? I know shops do it.

Thanks
 
Simplegreen and a crockpot.

Bring thr green up to temp soak for as long as you want (at least over night) and rinse.

Tecnique works well on chicken too. OR is that "It tastes like chicken" :roll:

Rico
 
I'm not sure if vinegar would work against varnish and other goop left behind by gasoline. Usually a penny is tarnished by the surface oxidizing, and the vinegar attacks the oxide.

Maybe this will work better:

carbboil.jpg


(Just kidding.)

Dave
 
How about brake cleaner boiling over an open flame? :twisted:

I'M JUST KIDDING ... DON'T TRY THIS!!!!!!!!!!!

Incidentally, don't soak anything in toxic chemicals unless they're outside ... the fumes will get you good! ... and remember that using anything that will break down those petroleum deposits may also do a number on any plastic or rubber parts/seals that are attached.

Steve 8)
 
As an avid R/C pilot I can tell you that the worst cleanup out there is the Alcohol/Nitro/Castor Oil cleanup on an engine.

Best kept secret I guess in this area is the Antifreeze soak.

If you follow these directions be sure to NEVER use the Crock Pot again for cooking food.

Strip your carb of all rubber pieces first.
Fill the Crock Pot 3/4 full with plain old Antifreeze.....Ethylene Glycol
and heat on 3/4 to full.
Drop your carbs in for 18-24 hours.
Shut the Crock Pot down and let it cool a bit.
Don your rubber gloves and take the carbs to a water bath with a tooth brush for any bad deposits.
Lastly, use some WD40 or Marvel Mystery Oil to LIGHTLY coat the surfaces
inside to hold off corrosion.
Once you are ready to reassemble the carbs use carb cleaner to clean off the oils.

With R/C engines this would clean off the WORST caked on gunk you could find!!

8) Hope that helps!!!!
 
Speaking of R/C

I wonder if nitro cleaner would clean bike parts? It's never hurt the rubber and plastic parts on the R/C cars. HHMMM May try it, I have a few cans of cleaner and some spare bike parts laying around the shop.

Okay back to the thread, I never knew Antifreeze would clean things, Great Tip!

I think I'm going to start dipping parts in various substances to see if I can formulate any bright ideas. I bet peanut butter on a chain would be awesome!
 
You must log in or register to reply here.
Back
Top