• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Chain Installation

  • Thread starter Thread starter rickt
  • Start date Start date
R

rickt

Guest
I'm trying to get as much done as possible on the '78 GS750C restoration before the snow flies. This afternoon, I got the engine cases installed and got a start with the new chain (RK Takasago 630). All went well until I attempted to install the master link. The instructions on the box indicate that I should use a press-fit tool to install the plate and not vise grips. I thought the benefit of the master link was that I didn't need a "special" tool.

Any suggestions on how I can get the plate and clip mounted?

Thanks
 
Do you have the kind of link that requires peening over the pins or the type that takes a clip? If you have the clip type, it doesn't matter what you used to get the plate compressed enought go get the clip installed. I used a C-clamp but others have gotten away with pliers of different types. If you have a standard type peen over master you need to use the special tool or peen over the pin before you install the chain - swing arm will have to be installed if you go this way.

Good luck.
 
I use to use a big pair of channel locks and a plain old nut, (8mm I think, you need one big enough to go over the pins) to squeeze the side plate on. Switch from one pin to the other often so you don't get it too cocked. Only press it on as far as it takes to be equal with the side plates on the rest of the chain, and of course far enough to get the clip on.

Make sure you put your o-rings on first if your link uses them, don't ask how I know to mention this. :P

Also, its best to put the clip on sharp side out and of course have the closed end of the clip going in the direction of rotation.
 
Clip Type

Clip Type

It's the clip type master link. I chose this type because I don't have tool needed to peen the pins. All my previous experience with master links didn't require any real force to install the plate. I guess this type of chain is different? I'll give it a go with pliers or vice grips.

Thanks
 
rickt said:
It's the clip type master link. I chose this type because I don't have tool needed to peen the pins. All my previous experience with master links didn't require any real force to install the plate. I guess this type of chain is different? I'll give it a go with pliers or vice grips.

Thanks
Click to expand...

I just installed my chain and I ended up using a C clamp with a 8 mm wrench to put over the pin. Worked great to squeeze down. You could even use two wrenches and do both pins at the same time. Or just work it back and forth.
 
Excellent suggestion

Excellent suggestion

Put a couple of nuts over the pins. Used a C-clamp on one and vice grips on the second. Pushed the plate on by slowly compressing the clamp and vice grips. Perfect result! Now I have to get back to sorting out my electrical wiring mess.

Thanks for the help.


portdave said:
I just installed my chain and I ended up using a C clamp with a 8 mm wrench to put over the pin. Worked great to squeeze down. You could even use two wrenches and do both pins at the same time. Or just work it back and forth.
Click to expand...
 
Glad you got it figured out. I ended up getting a new wire harness for my bike and redid all the main wires. Sure cleared up a lot of issues. Too much cutting into the harness over the years.

God bless and best wishes....

Rode home from church today. Sure was beautiful.
 
You must log in or register to reply here.
Back
Top