• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Compression Test?

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
i hear everyone talking about their compression in their engines and how anything under 110 psi is time for a rebuild. how do i go about getting a compression test done, or doing it myself (somehow to save money) on my '80 gs 400L. I would like to see what state my engine is in. Is it just a contraption like a voltmeter? or how does it work?
 
You will have to buy or borrow a tester. Preferrably one that screws into the spark plug hole as that is a bit easier to use. It is basically a pressure guage that measures how much pressure is being generated in the cylinder.

Testing is best done when warm. remove all spark plugs, and hook up the tester to each spark plug hole one at a time. Ground out the spark plug wires to avoid damaging the ignition coils. Open the throttle and press the starter button to turn the motor over a few times. In a few rotations of the motor the compression should be at maximum. Any more turns than that to get to maximum indicates a problem. The throttle needs to be open to get a true reading.

If the readings are low (less than 120psi) put a small squirt of oil in that cylinder - this will seal the piston rings. Test again. If the reading goes up to a reasonable level , the problem is likely worn rings/bore. If not, a valve problem.

This is a real simple explanation. If you have a friend who knows how to doi this on a car, the principle is the same.
 
you can buy a tester at canadian tire. I bought one but i got the cheap one($35) so it didn't have the proper end for a motorcycle now I have to make one. So spend the money about 50 dollars and make sure that it will fit on your bike. Take a spark plug with you for size. They will work on any engine. They have instructions in the box as well.
 
None of the ones at Canadian Tire will fit a D (10 mm) spark plug, just the B (12 mm) NGKs. After a bit of thinking it may be D is 12 mm and B is 14 mm.

Steve
 
Saaz,

You mentioned grounding out the spark plug wires, how do you do that? Is it as simple as putting the spark plugs back in the wires and then resting them alongside the engine?

Thanks,

Scud
 
"B" NGK plugs = 14mm and "D" NGK plugs = 12mm

I use a compression tester that has no threaded end. Its end is rubber and you press it in the plug hole. Works great and you don't need adapters.
 
I bought one at Sears for $29 and it comes with 5 adapters, both double ended. It fit's my snowmobile and my boat, both of which have odd size plug bores.
 
Id think Id have a bit of a problem holding a rubber compression tester in the hole, and holding the throttle open, and holding the clutch in... whew, thats alot of hands.

a good compression tester will set you back a bit, but is worth every penny if you are going to work on your own stuff.

read the manual's procedure for the test if you can, it ensures the best results. I run the test cold, then hot. and I just unplug the power wires from the coils, rather than grounding the hi-tension leads. easier to get at the middle plugs with the tank off anyway.
 
You must log in or register to reply here.
Back
Top