• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Doh.....darn butterfingers

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
I was putting the head back on my 81 GS750, and dropped a washer down the passage that the cam chain goes. I have tried several time to get it out with a magnet, to no avail. I can't see down there, and would rather not take the head off again. Can i pull the oil pan off and find it? or maybe turn the crank by hand a few times and find it? On the oil filter?any ideas about the easist way to do this would be appreciated.

Also, are the oil filters a clean and replace type, or should I buy a new filter? I still havn't taken it off yet, but I know I need to, I had a TON of gas in my oil.
 
Oil filters are cheap. I replace it everytime I change the oil. Check out dennis kirk kind of places, those are usually cheaper then a dealer. I buy in bulk, so I only purchase filters once a year and have them on hand incase I need them.

don't know about the washer...sorry :?
 
I did something similar once, couldn't get at it from the oil pan, ended up pulling the engine(1100) and shaking it upside down until the piece of crap fell out, keep trying!!!
 
I would think turning the crank would be a Bad Thing?. You might try taking the pan off, but you'll probably have better luck removing the engine and turning it over to shake it out.
 
Are you trying to go around the chain to get to the bottom of the engine to look for the washer?

I dropped an item down my engine and spent a while trying to find it by looking in front of and behind my chain. Finally I sat down and considered that maybe the chain itself had caught the piece, kind of like a net. It had, and I was able to get it out after just a second or two.

Good luck.
 
Don't think you should turn the crank- if the washer is hung up in the cam chain it may bind in the cam chain sprockets. Everytime I have the head off I have nightmares of this exact thing happening! Hope you can get it out ok.
 
Can I pull the motor with the head still on it? I was using just a touch of gasket sealer, so I tourqed the head bolts down, and don't want to pull it off now......

I was hoping to get access via the oil pan, but I guess you can't see the bottom of the crank/cam chain from there?
 
I would take the oil pan off first If you are lucky it will be there. Other wise Try shaking the bike to see if it falls out. or Take the cam tensioner guide out and shake the chain
 
Coworker (doesn't know bikes real well) said maybe I should just turn the BIKE upside down, instead of just the moter.


Hmm....hook up the rear tire to a block and tackle and start pulling.....

I have removed the front, plastic guide, but not the rear one yet I have been shaking the chain, and trying in front and in back. Guess I'll pull the oilpan off next.
 
UPDATE:

Well, I ripped the oil pan off last night, and sure enough, no way I'm finding tha from there. It was a good thing I did it though. My petcock had leaked lots of gas into the crank (I knew this from draining the oil earlier) and I used some gas as a solvent when cleaning the bike up. The bottom of the oil pan was NASTY with lots of thick, black sludge, that I hope came off of engine parts and such, and means my engine is fairly clean inside. I am soaking it in degreaser, and will clean it all off tonight.

I was unable to fish that damn washer out though, so the head is coming off. I may be able to get in and find it then, but if not, then I have to pull the next part of the engine off. Not sure what that one is called, or how to do it, back to the manual I suppose.

Q&A time:
If I have to get that deep in, I'll be pulling the pistons out. How can I tell if my rings are OK?

Where can I get an kit to put oversized pistons in, and what size can I put in an 81 750? Would it be worth it to bore it out if the pistons are in ok shape? The cylinder walls are nice and smooth, very clean. Didn't test compression, but I think it was good.

If I don't want to deal with this, and just wanna sell the motor to someone who wants to rip it down, what size moter will bolt on without many mods? 850, 1000, maybe a Kat engine? (not sure what size Kat's there are)


Thanks for any and all answers. I am beating my head on the wall, as I should have been riding now, but instead, I'm pulling it back apart.


___________________
Nick Weaver
Boise Idaho
'81 GS750L in many pieces
 
nweaver said:
UPDATE:


If I don't want to deal with this, and just wanna sell the motor to someone who wants to rip it down, what size moter will bolt on without many mods? 850, 1000, maybe a Kat engine? (not sure what size Kat's there are)


___________________
Nick Weaver
Boise Idaho
'81 GS750L in many pieces
Click to expand...

80-83 GS1100 (16v) engine will bolt right in with only the bottom center engine mount not lining up which is not totally necessary. Notice my signature.
 
Wll, I was somehow able to get the washer out with the magnet. \:D/

I put the cams back on, timed it, and am just about to bolt the valve cover back on. Then I have to get my oilpan gasket (8 BUCKS FROM THE LOCAL DEALER) and I'll be back on the road.

:-k Anyone had luck with making gaskets for temporary use? I have a roll of cork that is used for gaskets, and was going to cut one for a week's use. I want to change the oil in a week, so I get any remaining sludge out quick, and then I will put the real gasket and a new oil filter in.
 
nweaver said:
UPDATE:

Well, I ripped the oil pan off last night, and sure enough,
Click to expand...

How'd you do it I un did all my bolts and could get the things off

As for the washer, if it's steel the a magnet probe through where the cam chain goes should do it, I know I just fished the cam wheel bolt out of mine!!!
 
Oil pan has bolts all the way around it, and then one just forward of the drain plug. I did that, then I had to put a screwdriver in JUST THE COVER part of the hole, and wrench it off. Took quite a bit of effort, the old gasket was very hard and brittle. Felt like hardened rubber. I worked my way round the holes, putting the screwdriver in, and pushing in toward the center to flex it away at the edge. I did this a few times, and then I was able to push in one corner, and get a flathead screwdriver in and work it around. I don't think that has EVER been off my bike, based on the gasket. 8O
 
You must log in or register to reply here.
Back
Top