• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Float Level On Gs550 Carbs

  • Thread starter Thread starter Suzuki_Don
  • Start date Start date
S

Suzuki_Don

Guest
A question for those that are in the know on carburettors on this forum. With experience preferably. In all three workshop manuals that I have for my GS550B (1977) model, and that includes Suzuki Factory manual, Haynes and Clymer, they quote the float level at 26mm whereas all references on the forum refer to 24mm as being the measurement for the float level. Would someone more knowledgeable than me be able to give me the correct figure and explain why the differences are quoted. My bike has always run rich but with plenty of power and no evidence of lumpy running. I've discovered the float levels are set at 23mm. Would this be the reason for this? If set at 26mm would this be too lean?
Cheers. Don
 
Stats?

Stats?

I don't know the specs for your bike but I think there is WAY too much consideration given to the float levels. They're almost always set right to start with, almost never need adjusting and almost never cause problems. It just seems to be a 'fun thing' that people want to concern themselves with.

The chances are, if you have gas leaking out of the carbs...it's not the result of the float heights. It would be very unusual unless someone came in to your garage, took your carbs apart and adjusted your carb floats....without you knowing about it.
 
Float height is 24mm +- 1.0mm. I believe Suzuki made a mistake on the height at one point in the factory manual but corrects for it later.
 
Nessism said:
Float height is 24mm +- 1.0mm. I believe Suzuki made a mistake on the height at one point in the factory manual but corrects for it later.
Click to expand...

Thanks for that Nessism. I will go with the 24mm. Do you think 23mm would make it a bit rich. I notice that you have two 550s. Which one do you prefer to ride as far as the CV versus VM carbs go. I think the VMs are a bit harder to pull down than the CVs. Lots of bits on the throttle rod and choke rods that have to be replaced in the correct order. Will have to take lots of photos to get it back together right.
Thanks again. Cheers. Don.
 
chuckycheese said:
I don't know the specs for your bike but I think there is WAY too much consideration given to the float levels. They're almost always set right to start with, almost never need adjusting and almost never cause problems. It just seems to be a 'fun thing' that people want to concern themselves with.

The chances are, if you have gas leaking out of the carbs...it's not the result of the float heights. It would be very unusual unless someone came in to your garage, took your carbs apart and adjusted your carb floats....without you knowing about it.
Click to expand...

Except that they are usually different. Not sure why but it seems whenever I get another bike there are always one or two floats that are way off from the others.
 
chuckycheese said:
It would be very unusual unless someone came in to your garage, took your carbs apart and adjusted your carb floats....without you knowing about it.
Click to expand...

But I don't have a garage. I guess that would make it easier for him. Except I could see him out of the kitchen window.
 
tkent02 said:
Except that they are usually different. Not sure why but it seems whenever I get another bike there are always one or two floats that are way off from the others.
Click to expand...

At the present time I am still working on No. 1 carb and it is 23mm. I have not checked the others as yet. It will be interesting to see if and by how much they are different.
 
Check 'em!

Check 'em!

tkent02 said:
Except that they are usually different. Not sure why but it seems whenever I get another bike there are always one or two floats that are way off from the others.
Click to expand...

I definitely agree with you that they should be checked! As long as the carbs are off and disassembled, you might as well check them (and I always do). My point is that so many mechanical parts do get 'out of whack' over time; I just can't understand how that could happen to float levels. By the way, I've rebuilt many carbs and have never adjusted one yet....but, checking them is part of the ritual!:-D
 
Call me funny but I usually try to get the carbs as close to perfect as possible. There is always going to be measurement error so having the adjustment at nominal provides a little fudge factor.

Regarding the carbs at 23mm, that's on the rich end of the spec. The carbs in my 850 were consistently adjusted that way from the factory so I was happy to leave them that way.

Good luck.
 
Nessism said:
Call me funny but I usually try to get the carbs as close to perfect as possible. There is always going to be measurement error so having the adjustment at nominal provides a little fudge factor.

Regarding the carbs at 23mm, that's on the rich end of the spec. The carbs in my 850 were consistently adjusted that way from the factory so I was happy to leave them that way.

Good luck.
Click to expand...

Yes. I'm funny too. Thanks Nessism.
 
You must log in or register to reply here.
Back
Top