• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Fork oil

  • Thread starter Thread starter SeanMora77
  • Start date Start date
S

SeanMora77

Guest
I'd like to add fresh fork oil but have never done so. Can anyone tell me an easy way to do this?
 
Do you want to simply "add" or do you want to do it properly? :-k

You have to KNOW how much oil is in there, and the manual says that the proper way to measure the oil is to have the spring removed and the fork fully-collapsed and vertical. The only way to do that is to have the forks off the bike.

You can probably get quite close if you leave the forks in the bike, but you still need to remove the caps and the springs so you can measure the oil level to make sure they are the same.

.
 
The forks are off the bike, I want to remove any old and fill with new. I want to do everything properly. ;)
 
Remove the top cap. Extract the spring and spacers. Dump out the oil. Add fresh oil per the amount listed in the Suzuki factory service manual.
 
.........................................
thiagree.gif


.
 
Are you going to tell him what happens when he removes the top cap?
I also prefer to flush out the stuff in the bottom of the forks using ATF until it becomes ATF fluid color instead of that yucky, smelly grey.
 
With the fork fully extended it will only pop up about 1/2 inch ( 12 or 13 MM at the best..easily puhed back on by hand to start the threads.
 
Steve said:
Nah. It doesn't usually fly very far. :eek:

.
Click to expand...
Steve, you made me fall out of my chair. Shame on you! :D:D:D
Sean, the cap will pop up when you finish unscrewing it. How much it pops up depends on the amount of preload is in the spring and a possible spacer that may (or may not) be in there with the spring. If you have never had the cap off before be prepared for it, keep the pressure on it and let it up slowly. It may not be much at all, but you will not know until you remove it.
 
And I am serious about flushing it. There will be a tiny (usually Phillips) screw at the bottom of the fork. If you remove it a bit of gunk will flow out. I like to pour some ATF in the tube and let it dribble out the bottom. At first, it will be a yucky grey color.keep flushing it until it comes out ATF red. Let that drain completely and then reinstall the screw. Be careful with the screw; there is a tiny o-ring there and you do not want to damage it.
 
Runs some diesel or kerosene and it will flush and clean a bit better than just ATF. Ane even put it in and put the cap back on and turn the fork end for end a bunch to swish it around and scrub it out a little bit.
 
Here is a tip for putting the cap back on:

Before putting the spring in, put a mark on the cap (a Sharpie works well), start threading the cap on just a little bit. Unscrew it VERY SLOWLY and note exactly where it dis-engages the threads. Mark the tube with a line that aligns with the mark on the cap. Verify (by threading the cap back in) that that is where the threads will engage. Now put the spring back in, along with any preload spacers that you might need, you will know exactly where to place the cap so it starts to engage threads with the first turn. :D

OK, K_K, does that make up for it? :-\\\

3
 
chuck hahn said:
Runs some diesel or kerosene and it will flush and clean a bit better than just ATF. Ane even put it in and put the cap back on and turn the fork end for end a bunch to swish it around and scrub it out a little bit.
Click to expand...

Good idea Chuck.
I just use solvent.
Same results... CLEAN. ;)

Eric
 
When flushing with solvent stroke the fork a few times to run it through all the little orifices the oil goes thorough.
 
Billy Ricks said:
When flushing with solvent stroke the fork a few times to run it through all the little orifices the oil goes thorough.
Click to expand...
When you put fork oil in, do the same thing to get all the air out of those passages before trying to measure your oil level.

.
 
Steve said:
When you put fork oil in, do the same thing to get all the air out of those passages before trying to measure your oil level.

.
Click to expand...
Good advice. It takes a village to get all the little tidbits assembled.
 
Running ATF as fork oil for a few days riding will get the insides of the forks very clean.
 
You can tap them up and down on a block of wood too ..just like mom used to bounce the cake pan around to get air bubbles to rise out.
 
why not just put the right amount of fork oil into a measuring cup and put the same in each fork

and to clean my forks I just used some Varsol, sloshed it around, drained and repeated until it was all clear, let them dry out overnight and added my oil, put in the springs and put the caps back on...

easy...
 
You must log in or register to reply here.
Back
Top