• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

ignition problems on 83 gs850

  • Thread starter Thread starter scout127
  • Start date Start date
S

scout127

Guest
I am still trying to figure out my ignition trouble. I decided to start over from the beginning and check the basics. I am getting no ohms reading when I do a signal generator test, but my plugs do spark. However, it is not a very strong spark. I am also losing a volt from battery to coils...my coils read just over 11volts.

I plan on do the "coil relay modification" found on basscliff's website, but I'm concerned about the failed signal generator test. Why would I still get a spark? Also, my ignitor failed it's test. I just replaced the ignitor with a salvage one. Both ignitors have failed the test. Is there another problem I should be looking for? Faulty wiring or connector, etc...?
 
yeah,
igniters fail tests usually in these forums for some reason but if it fires it's good.

Because...

You MUST use an analog meter, not a DMM (Digital Multimeter).
If you don't have one, use the 1.5V cell.
 
Last edited:
Hi Mr. scout127,

I think the ignition test is on page 17-29,30 in the 850 Suzuki Shop Manual.

Here's a couple of procedures that I've collected:
Ignitor/signal generator/coil test
Originally posted by Mr. Billy Ricks

This is for an '85 700 but you can probably use the same tests for your bike.

Here's how to check the ignitor. Remove spark plugs 1 & 2 and ground them to the motor so they will fire when they get power. With the ignitor facing you, the plug on the right side of the ignitor is where the signal generator plug fits. The two terminals on the right side of that portion of the ignitor will be pin 1 at the front and pin 2 at the back. The two left pins will be pin 3 in front and pin 4 at the back. Turn the ignition switch on. With a multitester set a the X1 ohm range put the + probe on pin 2 and the - probe on pin 1. Plug number 1 should fire. Next put the + probe on pin 4 and the - probe on pin 3. Plug number 2 should fire. If this happens the ignitor is good and the signal generators are suspect.

As for testing the pickups, signal generators, measure the resistance between the two wires on each pickup. You should get somewhere around 130-200 ohms. If the resistance is infinity or less than spec they are shot.

To test the coils put one probe of the multitester on each of the terminals on the primary side of the coil. You should get 3-5 ohms. Check the secondary windings by placing one probe into each of the plug wires coming from one coil. Those would be 2 & 3 from one coil and 1 & 4 for the other. You should get 30-50,000 ohms for stock coils and 15-20,000 for aftermarket.

Testing The Ignition System
by Mr. Matchless

Properly localizing a problem with the ignition is sometimes a bit confusing and the following below should of assistance:

  • Basic test, remove spark plugs. Fit them to the plug HT leads and ground them to the engine. Turn engine with starter and see if plugs spark. If any one spark plug does not spark swap it out. If the spark seems good on all 4 plugs, the ignition system is very likely in order. If spark is not present or very weak proceed with the following tests.
  • Remove the tank, left side cover, seat and signal generating unit (pickup) cover at bottom right of engine.
  • A good habit is to check the coils and igniter to see if they do not get very hot once the ignition is switched on, as this will most likely be the indication of a failed component of faulty connection or wire.
  • If the spark is weak but present, inspect the HT leads and plug caps. Suspect coil wires and spark plug caps, or voltage at the coils and thus the battery condition. It could also be due to coils with partially shorted windings, but do not jump on this cause immediately, and they may get hot.
  • Overheating coils with no spark may also be due to them getting a permanent full ground either from a faulty igniter or a grounded and pinched wire. Disconnect the coil plug connectors and proceed with tests.
  • Measure the battery voltage directly across the battery terminals. If lower than approximately 12.6V first charge battery fully before proceeding.
  • Next measure voltage over the coil connector plug, orange/white wire and the battery negative terminal. If lower than 12 Volt inspect the wiring for poor contacts and localise cause of voltage drop.
  • Again measure directly across the battery, but pull off the spark plug leads to prevent engine from firing and swing with starter. While starter is turning the voltage should stay at least above 11 Volt. Also swing the starter with the headlights on to see that the voltage does not drop significantly at the coils while the starter plus headlights load the battery, which could prove that even if your battery is fully charged, it cannot give full or sufficient current and is on its way out or your starter may be drawing excess current (usually unlikely if starter is spinning at full speed) and pulling the battery down. If it drops much lower, charge battery fully or have it load tested and replaced if faulty.
  • If all is well up to here you can assume your battery and the positive feed to your coils are in good order.
  • With the coil plug connectors disconnected, use an ohm meter and measure the resistance of both windings on each of the coils. Exact resistance measurements are not too important, but continuity of the windings close to the approximate resistance values given indicates that the coils are in good condition. It must be noted that it is possible for the coils to only show up a fault when at higher operating temperatures, but this does not happen frequently.
    Ignition coil resistance:
    Between the two HT plug caps of the same coil, secondary HT winding, approximately 30 ? 35 K ohm
    Between the orange/white and white on the first coil and orange/white and black/yellow on the second coil, primary winding, approximately 2-5 ohm. If this test is within limits you likely have two good coils.
  • Locate the igniter and disconnect the plug with the blue and green wires coming from the signal generator (pickup) at the right bottom of the engine. Test the resistance across these wires coming from the signal generator pickup coils, it should be approximately 250 ? 360 ohm. If this is in order you have proved the pickups and the wires to be good.
  • The little back box or igniter is now tested as follows. With the ignition on, kill switch on, test for 12 Volt DC between the orange/white and the black/white wires in the plug going into the igniter. This proves that it is getting the correct voltage.
  • The next step is to prove whether the igniter is powering your coils. Remove all 4 spark plugs and connect the HT lead caps to a spark plug #1, #2, #3 and #4 which is grounded and located to enable you to see the spark. Ensure all the connector plugs are back in, except the one with the green and blue wires from the signal generator.
  • To simulate the small voltage generated by the pickup coil, prepare an ordinary 1.5V dry cell with two wires red for positive and black for negative. Connect the negative black wire from the dry cell to the blue wire on the connector plug going into the igniter. Switch on the ignition and kill switch to power the igniter and briefly touch the red wire from the dry cell positive to the green wire connector going into the igniter. You should see a spark on plugs #1 and #4 when you touch the wire and on #2 and #3 when you remove the wire. If this works your igniter is in a working condition.
  • One other check that is often overlooked. Run the bike at night with all lights off in a dark area and check that no sparks are jumping from the HT leads to the frame or tank. If so they may need replacing.
  • At this stage if all tests have passed you MUST get a spark at all the plugs when everything is reconnected and the engine is turned with the starter.
  • If a spark that was previously missing has mysteriously appeared, have a very good look at your wiring and connectors, as something may be making intermittent contact and corrected itself temporary when you moved the wires.
  • If there is a spark, but the engine will not fire, it could be due to ignition timing, valve timing or fuel problems. Ignition timing and valve timing problems are more likely on a bike that has not run yet after being disassembled and more unlikely to be the cause if the bike was not taken apart and was running before.
  • A quick test with a few drops of fuel directly into the cylinders before replacing the spark plugs and then trying to start will prove it to either the fuel system or ignition system.
    1. If the engine then starts and runs for a few RPM's the ignition is correct and you need to look at the fuel and carburettor side.
    2. If the engine does not fire, but occasional gives one load pop through the carburettors or even exhaust, it may be igniting when the valves are open, the valve timing may be a problem, cam chain or swapped wires from pickup ? plugs firing at wrong time.
    3. Other reasons could be extremely low compression, too tight valve clearances, thus not closing fully (usually unlikely on all cylinders at the same time, but plausible), carburettor faulty or dirty, fuel line, filter or petcock faulty. Filter can cause an airlock if not positioned properly to allow free gravity feed.
    4. Then finally the ignition timing must be set properly. At less than 1500 RPM connect a timing light to #2 or # 3 spark plug and check that the timing marks line up for 2-3 on F, then move to #1 or #4 spark plug and check that marks line up for 1-4 on F. Check the advance by pushing revs up to 2350 RPM and the timing marks should both line up on the 45 mark behind the signal generator mounting plate through the sight hole at the top. The three mounting screws can be loosened and the mounting plate can be moved slightly in the elongated holes to meet this.


Best of luck to you.

Thank you for your indulgence,

BassCliff
 
You must log in or register to reply here.
Back
Top