U
UncleMike
Guest
What do you guys think? If I attempt to use the impact driver on the CV cap screws, am I gonna break something?
-
Required reading for all forum users!!!
Welcome!
Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.A note to new registrants...
All new forum registrations must be activated via email before you have full access to the forum.A Special Note about Email accounts!
DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.A note to old forum members...
I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.
Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...
-
Returning Visitors
If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.
If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.
D
ddaum
Guest
I don't know about the impact driver. When I was doing mine, I just used a small set of vice grips and gripped the side of each screw and turned them to break them loose. Then remove them with a screwdriver. I replaced all the screws with SS allen head hardware during the rebuild.
U
UncleMike
Guest
ddaum said:
I'm planning the same with the hardware.
For the vicegrips, I tried the same with a pair of pliers, but it's just not workin'. Should I go get some vicegrips instead?
frosty5011
Forum Mentor
Mike, If I was you, I wouldn't worry about damaging them at all. If they're a pain to get out, use either the impact wrench or a set of vice grips, whatever works best.
I would replace all those screws with Allen head bolts. It's what I do to every set of carbs, first time I take them off of a bike......mostly because some of them have the screws that are already damaged, or corroded, or have just been there for 20+ years and are a pain in the a$$ to remove.
I've always had luck getting the Allen head bolts in the required sizes at Ace hardware.
I would replace all those screws with Allen head bolts. It's what I do to every set of carbs, first time I take them off of a bike......mostly because some of them have the screws that are already damaged, or corroded, or have just been there for 20+ years and are a pain in the a$$ to remove.
I've always had luck getting the Allen head bolts in the required sizes at Ace hardware.
U
UncleMike
Guest
Oh, I wasn't worried about damaging the screws. I meant damage to the carb itself. I don't want to crack it or anything.
frosty5011
Forum Mentor
If they're in there THAT tight, and you've tried "carefully" with the impact driver to no avail, then try a good set of vice grips. If that don't work, then drill the heads off of the screws.
L
lapls
Guest
Hi,
I also had a hard time removing these screws, basically, you only have 1 chance to remove it, otherwise it starts to strip the phillips head, I used long noses wise grips and was able to remove the tough ones this way ( they are about 6 inches long , genuine wise grips ). Following the ecommendation from someone here, I also removed all teh bracket screws with my impact driver ( a good one.. small hammer with my Snap-on with brand-new bits, worked like a charm ). For each screw I took care to put a piece of soft wood behind, thinking that would absorb some of the impact..
It worked, and when putting them back I found that the best screwdriver was my impact , maybe because of the good grip and inertia ;-)
I also had a hard time removing these screws, basically, you only have 1 chance to remove it, otherwise it starts to strip the phillips head, I used long noses wise grips and was able to remove the tough ones this way ( they are about 6 inches long , genuine wise grips ). Following the ecommendation from someone here, I also removed all teh bracket screws with my impact driver ( a good one.. small hammer with my Snap-on with brand-new bits, worked like a charm ). For each screw I took care to put a piece of soft wood behind, thinking that would absorb some of the impact..
It worked, and when putting them back I found that the best screwdriver was my impact , maybe because of the good grip and inertia ;-)
U
UncleMike
Guest
Vicegrips worked nicely.
Thanks to all.
Mike
Thanks to all.
Mike
frosty5011
Forum Mentor
UncleMike said:
Also great for removing ingrown toenails!:shock: :-D
H
HiSPL
Guest
Also you wouldn't have damaged the carbs. They are tougher than you think....
U
UncleMike
Guest
Yeah, but now I got myself a new tool!
M
Macmatic
Guest
HiSPL said:
Tell that to the float pin supports!
But seriously... Vice grips work wonders but I was able to get out a couple that were getting too chewed up by the vice grips by just slotting the head with a hack saw blade and using a regular screwdriver.
/\/\ac
U
UncleMike
Guest
Macmatic said:
So far I've gotten the first float pin out with no damage. We'll see if I can keep that record up for the other three.
Tried the hacksaw method with one of the gangplate screws. No dice. Impact driver saved the day even after I hacksawed it.
H
HiSPL
Guest
Macmatic said:
Well don't use the impact driver there! LOL
The rest of the carbs are pretty tough.....
D
drohde
Guest
I took a Dremel tool and cut straight slots in the screws. The used a 1/2 flat blade with a handle large enough to put some real torque on the buggers. Replaced with SS philips screws that fit US drivers.
J
J_C
Guest
Dremmel was my saving grace as well. Same method.
H
Hoomgar
Guest
The Dremel tool was given to us by GOD himself I believe! I cannot imagine how I lived so long without one after getting one last weekend. No mater where it is, if you have snapped it off and do not have a Dremel tool, stop right where you are and go buy one before you try anything else! Take all your easy-out bits and weld little rings on them so you can use them as fishing sinkers.
Last edited:
U
UncleMike
Guest
Hoomgar said:
Dremel didn't do schit for me. Still wouldn't turn. Vicegrips worked wonders.
That being said, I've used the dremel to great success on just about every other endeavor, although I still prefer to do things by hand most of the time. I think of it as meditation.
H
Hoomgar
Guest
UncleMike said:
There is a trick to "customizing" the cutting disks in order to make them do what you need them to do depending on your issue. Glad you got them out Mike. Like Ron said, get yourself some good Allan head bolts from the hardware store now. I have no idea what Suzuki was thinking when they put all those screwdriver tip screws all over the bikes?
U
UncleMike
Guest
Hoomgar said:
It's honestly madness. Sometimes you really wonder.
"Screwdriver tip screws of a material that's both soft AND will chemically bond to carb and engine? Brilliant!"
Similar threads
