• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Incorrect Fuel Gauge Reading?

  • Thread starter Thread starter grantcrose
  • Start date Start date
G

grantcrose

Guest
So I had my carbs off this morning to replace the main jets. Finished up with that, replaced the carbs, tank, hoses, etc. as normal. After I filled her up with gas though, the fuel gauge reads only 75% full. The tank is definitely full. I checked the connections and they all seem solid as well. Anyone know what might cause this?
 
If the gauge reads low you bend the float arm down..if it reads too high..then bend it up. Same principals as setting the old style float in a toilet tank.
But, you need a mark to set things up to..and the only "for sure" mark on the gauge is the half full line.

So what I do is to find out the tank capacity per the manual first. If its a 5 gallon tank, then I pump 2.5 gallons at the pump. Put that in and turn on the key and let it sit a few minutes to really get a good reading..have the bike on the center stand also.

If it reads right at the half mark..no adjustment. If its off, drain the tank back into the can, remove the float and tweek the arm. Repeat till the reading is as close to the half full mark as you can get it and be happy. Now the sending unit is calibrated to the reading on gauge.
 
chuck hahn said:
If the gauge reads low you bend the float arm down..if it reads too high..then bend it up. Same principals as setting the old style float in a toilet tank.
But, you need a mark to set things up to..and the only "for sure" mark on the gauge is the half full line.

So what I do is to find out the tank capacity per the manual first. If its a 5 gallon tank, then I pump 2.5 gallons at the pump. Put that in and turn on the key and let it sit a few minutes to really get a good reading..have the bike on the center stand also.

If it reads right at the half mark..no adjustment. If its off, drain the tank back into the can, remove the float and tweek the arm. Repeat till the reading is as close to the half full mark as you can get it and be happy. Now the sending unit is calibrated to the reading on gauge.
Click to expand...

Best to get rid of the rust and corrosion before recalibrating it, don't you think?
 
I haven't seen any of the gauges that have been very accurate. It is not necessarily a bad thing depending on how it acts and what bike it's on. I have an '80 tank on my '78 with a petcock without a reserve. My gauge reads full when it's full but goes to half very quickly. It is consistent though, when it says it is empty, I have between 3/4 to one gal. of gas left depending on how I drive. That's my reserve.
 
Tom...eah..clean it when you take the sending unit out after the first test run...Ive never had one that was reasonably close enough for my liking anyway. Seems to me they are all off by a good margin regardless.
 
I had one that was absolutely perfect. Full tank read exactly full, it hit reserve right at the red, it ran out of gas the moment it read empty.

Probably a fluke.
 
Maybe..maybe not. all I am saying is that I like them to read as close as possible and the only known mark to register to is the half full mark. So I tweek them to where they are right on and reliable. Youll also note that on a cooler days, the bimetal strip looses heat from air rushing thru the gauges while riding and it will read low also...even after adjusting.

Stay still for a minute and it reads a bit fuller..take off and it drops off some again.
 
chuck hahn said:
But, you need a mark to set things up to..and the only "for sure" mark on the gauge is the half full line.
Click to expand...
Actually, there are several "for sure" marks on the gauge. :-k

The lines I see on my gauges are "F", "half", "red line" and "E".

Personally, knowing that the gauge reading is not quite directly related to the actual level in the tank, I choose to make my calibration point the beginning of the red line, which will happen as I need to switch to REServe. I don't care if the gauge stays on the "F" for a hundred miles, then drops like a rock, as long as when it approaches the red line, I KNOW that I will soon need to reach for the petcock. :D

.
 
but when you fill it up to about an inch below the filler neck it goes way over the "F" line..least mine do. Thats why i suggested to use the half full line...its a known spot and known quantity of fuel. You have 2 constants that will give the most accurate reading in my opinion.
 
You must log in or register to reply here.
Back
Top