• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Jetting question

  • Thread starter Thread starter tigerfan474
  • Start date Start date
T

tigerfan474

Guest
So I've been jacking around with my 82 550L for the last year trying to get it jetted right. I bought a 6 sigma jet kit and finally got it started! The 1 and 4 carbs have 107.5 mains and the 2 and 3 have 110's. Btw I have 2 k&n 2into 1 filters on the carbs. It only came with the main jets. I'm at 2 turns out on the screws. It also idles at 2500 3000. When I back the idle screw off it dies. Can't seem to get the idle any lower without it dying. Do I need to replace the slow jets as well? If so what size should I try?
 
Hi,

You probalby need to raise the jet needles too. I'm not familiar with that jet kit. Does it come with slotted needles? You probably need to turn out the idle mixture screws some more too, at least 3 turns.

If your kit did not come with slotted needles then you will have to shim the needles to raise them a bit. You'll find info about that on my website or just search the forum. It has been discussed literally 1000's of times. ;)

The Dynojet kit is the favorite around here.


Thank you for your indulgence,

BassCliff
 
Forgot to say that. It didn't come with slotted needles but it came with washers to raise them.I used the 3 washers per carb they sent. They also sent plastic spacers that are a little thicker than the 3 washers combined. I will check your web site more. Thanks
 
Let's go back to Square One and start with the basics.

Have you cleaned the carbs and replaced the o-rings?
If you haven't, there is no need for further discussion until you do.
If you have, it's merely a matter of adjustments.

How were the needles assembled?
Specifically, what is the order of washers, spacers and clip, starting at the blunt end of the needle?

Your idle issues are probably due to insufficient fuel in the pilot circuits. Soaking the carbs in the recommeneded "dip" will clean them out.
When the carbs are clean and re-assembled, start with the mixture screws three turns out, then adjust from there when the bike is warm.
You will also need to sync the carbs, which requires a special (not cheap) tool.

How is the rest of the basic maintenance?
Have you adjusted the valves within the last 3000 miles?

Let me know if you need help, I am close enough to do so and have all the necessary tools.

.
 
Steve, I have dipped and put in new orings. Got the kit from, I think, cycle orings. Let me go way back. I got this bike 2 years ago. PO said he parked it for the winter and it didn't start come spring. It had a bad petcock. Replaced that. Then I found this site and did the carb dip and put back all stock jets. Everyone one here said it would not run right or even start without the breather. They were right. I never had a breather. So I bought the k&n's. Then i bought different sized jets, then the 6 sigma jet kit. This past Wednesday was the first time I ever heard it run. About the previous maintenance. I have know idea. Valves adjusted? Not by me. I have not attempted that. I am 42 and new to working on anything. Just for me to get it started was hugh.
I have the screws at 2 1/2 out. I will try 3 and proceed from there. Thanks for your help.
 
The washers and spacers on the jet needle, how exactly are they positioned?

Did you add washers under the clip or above?

And will it idle with the choke on? How about with the choke off and the engine fully warmed up?
 
The washers were put on the underside of needle per instructions. They said it would need to be richer. I choked it and it fired up. It was running about 4200 rpm. Backed the choke off and it dropped to 2700 or so. I then turned the idol adjustment screw. It dropped to 2100 and died. Wouldn't start again. Then reversed the screw and it fired up. Running at 2300. This is where I currently stand.
 
tigerfan474 said:
The washers were put on the underside of needle per instructions.
Click to expand...

This does nothing but compress the spring farther. You need to remove some spacers above the clip, or use a thinner spacer above the clip, this lets the spring push the needle up a bit higher.
 
You must log in or register to reply here.
Back
Top