• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

newbie and a carburetor

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
Opinions please-

What are the collective thougths on whether a newbie, who's never done it before, could handle taking a carb off, cleaning and reinstalling it?

I have an '83 GS-1100-G with no mods, all original.
 
there's a million shades of newbie....are you mechanically inclined at all?...how do you feel about doing them, it's not real hard but you may need extraneous other skills if something breaks, precision and thoroughness count too, there's plenty to read up on here about it, do a search for carb rebuilding and get yourself a reading sandwich :lol:
 
The first time I did it, I was a little intimidated. Do you have a manual? Even if you don't, you can print the bikebandit.com schematic and use that. Once you get into it, you'll be fine.
 
Jethro said:
The first time I did it, I was a little intimidated. Do you have a manual? Even if you don't, you can print the bikebandit.com schematic and use that. Once you get into it, you'll be fine.
Click to expand...

Thanks for the info. Does that bike bandit website have a diagram that I can print off? If I sign up with them will they spam me to death? I'd hate to have my e-mail address sold off.
Thanks again for the help
 
daveo said:
there's a million shades of newbie....are you mechanically inclined at all?...how do you feel about doing them, it's not real hard but you may need extraneous other skills if something breaks, precision and thoroughness count too, there's plenty to read up on here about it, do a search for carb rebuilding and get yourself a reading sandwich :lol:
Click to expand...

Thanks Dave-
I have average skills but I'll be working on the bike at a buddy's garage and he has above average skills. I just hate to always ask him to help. He's already helped me alot with my '84 truck. If I can get a diagram I'm sure I can figure it out.

Thanks for your opinion.
 
You should have a good manual.
Some basics for the first timer:
It can help to make a quick video of your carbs. Slowly scan the carbs outside. This can help you go back and remember where a little washer or ? was or which way something went. You can video tape the insides too as you go. The diaphragm assy', the float/jet area...
Use good fitting tools.
Lay the carbs on a large towel to keep parts from rolling away.
Keep each carbs parts separate, don't mix.
Lay the parts out in order.
If you're worried about putting things back right, you can always do one carb at a time.
Don't let carb cleaner contact the rubber parts. If it does, rinse quickly with gas or kerosene.
Use compressed air to help clean the carbs passages. Verify the air escaping through a passage.
Be sure to count how far out your mixture screws are and keep a record. Be careful not to strip their heads. These screws can be tight.
Check all o-rings for condition. Also, the manifold o-rings will probably need replacing, if you have them.
Be sure to set the floats and be sure they are straight and not tweaked.
Buy a carb synch tool to make the carbs work their best.
 
I did mine a couple months ago. I'm not new to mechanics or carbs, just never worked on motorcycles before.

I printed out the whole carb section in the GS garage area. I used that along with my manual.

Keith pointed out very good ideas. Ones that I used anyway. I only did 1 carb at a time. Put it back together, then started on the next one. Mine were fairly clean and I didn't "Dip" them, so that may have made it easier to do 1 at a time. I also have access to microscopes and Eye loops, so as to check all the jets and passages. I found those to be very helpful.
After the first one, the rest were a breeze. They aren't really that complicated if you understand carbs a little. The Carb clean up series is totally awesome. I used that more than my Factory manual. :lol:

My problem was getting the carbs back in with my stock air box. :evil: :evil:

Good Luck. Actually, the cleaning and rebuilding of the carbs, I think, you will find quite fun.
Getting them back in? Let the pro's here give you some ideas before you try it.
 
My problem was getting the carbs back in with my stock air box.
Click to expand...

I think Earl would suggest pod filters :lol: :lol: :lol:
 
Reinstalling the carbs is easier if prepared. Before attempting, it is best to place a roll of gauze, a small can of liquid electrical tape, two dozen bandaids and a bottle of linement close by. After each attempt, coat the gouges in your fingers, wrists, and arms with liquid tape, wrap in gauze while the tape is still sticky and then layer with bandaids. Apply linement to your back, and then try again. :-)

Earl

DMPLATT said:
My problem was getting the carbs back in with my stock air box. :evil: :evil:
Click to expand...
 
Reinstalling the carbs is easier if prepared. Before attempting, it is best to place a roll of gauze, a small can of liquid electrical tape, two dozen bandaids and a bottle of linement close by. After each attempt, coat the gouges in your fingers, wrists, and arms with liquid tape, wrap in gauze while the tape is still sticky and then layer with bandaids. Apply linement to your back, and then try again.

Earl
Click to expand...

:lol: :lol: :lol: , forgot the beer and the notepad as to write down the new swear words you've created. :lol: :lol:
 
im a newbie as well, and that website is just perfect, it displays everything you need in a diagram
 
You must log in or register to reply here.
Back
Top