• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Proper oil checking position.

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
Hello fellow GS'ers,
I have searched a lot for the answer to this in previous posts, but have not found a definate solution. When I check my oil in my 82 GS650G, should it be on the center stand, or should I be sitting on the bike holding it straight and bending ovet to see into the sight window?
Thanks
Tom
 
I always do it on a level surface on the centerstand. I figure that in that position the site glass would show the oil as being lower than if it where not on the centerstand...I would rather have a little extra oil than a little less than what I needed.

Hap
 
I will take a look at it, so far the oil level is only visible through the sight glass when it is on the wheels and Im on the bike.
I f it is on the center stand I cant tell if it is reading completely full or completely empty.. (no line) and its kind of tough to watch what it does while putting it up on the stand..
Thanks for the info
Tom
 
I have the same bike as you, Tom. I check mine on the centerstand. When do you check yours? When it's stone cold from sitting overnight, or right after you shut it down after a run?
I usually wait 5-10 minutes before checking the oil level after a run.
 
I have only checked it when it is cold.. Maybe if I let her run a bit and heat up, it will register in the sight glass when on the center stand.. by the way, I tried that version of putting the bike on the centerstand that was discussed here in the forum not long ago, it worked great!.. I had been holding onto the handlebars as I would if I were on it and pulling like hell at the same time I tried to apply weight to the stand.. needless to say, I went the tough way about it.. thanks to whoever posted the tip.
Thanks!
Tom
 
If you're having a hard time finding the 'line' just balance the bike and look at the window. That way, you can rock the bike back and forth a bit to see the oil moving. Then you can do the centerstand way if you want, I took my centerstand off (exhaust), so I just do the balance thing any way.
 
the balance thing and the centerstand will give different readings of oil because of the position of the engine.

on the centerstand it will show less oil in the window when compared to balancing. this means guys who do the balance trick need to add just a bit more oil to properly reach the full mark if the bike were to be centerstanded.

~Adam
 
If you want to check with it on center stand have the rear wheel on the ground, front wheel up in the air, Best way is to change the oil& filter, put the correct amount of oil in the bike and then check the site window in relation to how you check the level weathe on the stand or on the ground
 
Proper position

Proper position

According to my Clymer manual on the '80-'81 GS's the proper position to check the oil level is on the centerstand, which if I had to guess would not be where I would check it since that is not how you go around riding the bike.
 
SqDancerLynn1 said:
If you want to check with it on center stand have the rear wheel on the ground, front wheel up in the air, Best way is to change the oil& filter, put the correct amount of oil in the bike and then check the site window in relation to how you check the level weathe on the stand or on the ground
Click to expand...

This will only work if you are putting oil in a brand new engine for the first time...my Suzuki shop manual says that there are different amounts depending on if you have a new engine and/or if you changed the oil filter.

Hap
 
the official Suzuki method for checking the oil level on our bikes is to put the bike on the center stand, on level ground, and to keep the oil level between the marks. "L" and "F"

No rocking, No pushing the back tire down, No voo doo, just sitting on the center stand.
on my 1000g when I change the oil and filter, if I drain it good (lean it back while draining) it will take exactly what the manual calls for, right on the full mark.
 
MY 750 has an opaque sight window, so the oil level is difficult to see.
I put the bike on the centerstand. Unscrew the oil filler cap and shine a flashlight into the filler. The oil level is then easy to see in the sight window.
When filling it with oil, the bike takes 3.2 qts if not changing the oil filter and about 3.5 if a new filter is installed. In either case, I just put in 3 quarts, open the 4th and shine the flashlight into the filler neck to see where the oil level is. Then I just add a few ounces at a time and check with the flashlight until it is on the full mark. In no case will I add more than 3.5-3.6 quarts.

Glad the centerstand "dance" worked out for you. Writing it out makes it sound more complicated than it is. Its just too easy now isnt it. eheheh

Earl




MAGICTOM said:
I have only checked it when it is cold.. Maybe if I let her run a bit and heat up, it will register in the sight glass when on the center stand.. by the way, I tried that version of putting the bike on the centerstand that was discussed here in the forum not long ago, it worked great!.. I had been holding onto the handlebars as I would if I were on it and pulling like hell at the same time I tried to apply weight to the stand.. needless to say, I went the tough way about it.. thanks to whoever posted the tip.
Thanks!
Tom
Click to expand...
 
The opaque sight window usually only happens in cold weather when doing short trips. Condensation build up.

Solution..go for a long ride :))

I did find whne the bike was standard that it used to fog up on the oil window mow. The othe solution is to hot the bike up....

Difficult choices I know....
 
You must log in or register to reply here.
Back
Top