J
Jmanor
Guest
Has anyone put a Tail Loop on? Looking at doing a Cafe Racer/Bobber project for my 82 GS1100GL. Where did you get your tail loop from (cost) and if any pics?
Thanks
Jeff
Thanks
Jeff
-
Required reading for all forum users!!!
Welcome!
Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.A note to new registrants...
All new forum registrations must be activated via email before you have full access to the forum.A Special Note about Email accounts!
DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.A note to old forum members...
I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.
Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...
-
Returning Visitors
If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.
If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.
J
Jmanor
Guest
Well actually you can use the same Tail loop for both.
G
Guest
Guest
Lots of them from Ebay for $25.00+
J
Jmanor
Guest
G
Guest
Guest
Here's one. Lots more available, cheap. I'll be ordering one for my cb550 cafe project.
http://www.ebay.com/itm/210mm-Motor...ash=item41b6d86a38:g:Qp0AAOSwMVdYGDoQ&vxp=mtr
http://www.ebay.com/itm/210mm-Motor...ash=item41b6d86a38:g:Qp0AAOSwMVdYGDoQ&vxp=mtr
Steve
GS Whisperer
The frame on my wife's 850L is 1", I doubt that your 1100L would have anything smaller.
Actually, I can guarantee they are the same size, they share a part number for the frame. :-\\\
.
J
Jmanor
Guest
Would this fit? 1" with 7/8 I/D.
http://carpyscaferacers.com/shop/hardware-clamps/cb750-steel-frame/
F
fasteddie313
Guest
J
Jmanor
Guest
That doesn't answer the question. How about you not be a dick per say and either say yes or no or dont reply. Some on this site as you may not know with the lack of post you have,actually have done stuff like this before and dont mind helping others.
G
Guest
Guest
As long as the od's are the same you can make a step bushing, or pin, to slide into the frame if the id's differ.
Distance between ends would be the only problem. I think you would have to cut your frame and give that fellow a center to center measurement to see if he'll custom bend one for you.
On second thought, see if he'll custom bend one before you cut the frame
Distance between ends would be the only problem. I think you would have to cut your frame and give that fellow a center to center measurement to see if he'll custom bend one for you.
On second thought, see if he'll custom bend one before you cut the frame
Last edited:
