• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Torque wrench question

  • Thread starter Thread starter Guest
  • Start date Start date
G

Guest

Guest
Just got my silicone valve cover gasket from Real Gasket in Tennessee to fit my 1978 GS1000. I found a Sears Craftsman 3/8 inch drive torque wrench calibrated from 5 to 80 ft. lbs. at about 90 bucks retail.

My question: is this a versatile enough torque wrench for other work on my bike or should I throw down some more money for a bigger wrench?

Thanks,

Jack
 
Torque

Torque

I'd phone the service department at a bike shop and ask them....they'd know the answer to that one, for sure. Also, if you're thinking you may just need it for that job...for now, quite a few of the auto parts stores have tool loan programs...places like NAPA, Kragen, etc. You could go in there, buy a case of oil and I bet they'd be happy to help you out! :lol:
 
Throw down some money for a smaller wrench. Especially one calibrated in inch-pounds. A tremendous number of the fasteners go to 7 foot-pouds MAX, and the torque wrench is usually most accurate in the middle of the torque wrench's range.

Harrison
 
My question: is this a versatile enough torque wrench for other work on my bike or should I throw down some more money for a bigger wrench?
Click to expand...

You will need a smaller wrench, not bigger. The biggest torque required on my ZX-9 is about 80ft*lb (I think it is) for the axles and everything else is less. Mostly WAY less. You could use the wrench mentioned for bigger fasteners, but you should get a smaller one that runs from 0-200in*lb for the smaller stuff.

The dial type are the most accurate, but not cheap and are sensitive to operator technique. Also they are not that convenient when trying to torque a fastener in an awkward location. The click type are most common, but require frequent calibration to maintain accuracy. They are also the most convenient for the awkward to reach stuff. The beam type are good if calibrated and used carefully and are very inexpensive. They have the same issues as the dial type wrenches regarding technique and hard to reach places.

Mark
 
I have a couple of torque wrenchs. However, I usually find myself using this one on my motorycles.
00944642000-190.jpg


Only 19.99 and it measures from 0-75 ft-lbs.

http://www.sears.com/sr/javasr/product.do?BV_UseBVCookie=Yes&vertical=TOOL&pid=00944690000
 
I believe that the Real Gasket requires about 15 inch-pounds. That is less than 2 foot-pounds of torque. If you try to use the 5 to 80 ft-lb wrench you will not get accurate results.

Inch-pound torque wrenches normally go down to 25 in-lbs. There are some that go down lower but they are VERY expensive and hard to find. I would tighten the bolts finger tight and maybe a 1/8 turn beyond but that would be all.


Hap
 
I have a Sears Craftsman 5-80. It will do the majority of the bike. The smaller carb hardware can require 3 ft/lb, etc. For these I rely on experience/feel. No problems.
For that silicone gasket, I would do like Hap says. Just finger tight and then a bit more. If it leaks anywhere, give it a little more. It'll stop.
PS: I never thought I'd answer another torque wrench question! :wink:
 
Haha! I was watching to see if you would "weigh in", Keith! :lol: :lol: :wink:

Steve 8)
 
What do you guys usually torque? There's a spec for everything but I usually only torque stuff like the cam cover and cam caps. If it isn't in the engine or bolted to it I don't bother. If something comes loose instead of torquing it I toss on some blue loctite.

Steve
 
srivett said:
If something comes loose instead of torquing it I toss on some blue loctite.

Steve
Click to expand...

AH! a future Harley owner in the making!! LOL :lol:
 
You got me Leon! I just bought a D401 Harley Davidson branded tire for my 1100. On top of that, the 1100 I own was traded in for a Harley! hehehehehe

Steve
 
What do you guys usually torque? There's a spec for everything but I usually only torque stuff like the cam cover and cam caps. If it isn't in the engine or bolted to it I don't bother. If something comes loose instead of torquing it I toss on some blue loctite.
Click to expand...

If there is a torque spec I use it. They are there for a reason, especially on brake components, the countershaft sprocket nut, the rear sprocket nuts, and anything else that will cause serious issues if it comes loose while I am cranked over in a turn. I find it especially important to follow the values for the smaller fasteners. The last time I installed new pads in my front calipers, I found the mounting bolt torque was WAY less than I would have done by "feel" and I may have risked twisting a bolt off with possibly dire consequences. I don't find it that time consuming or difficult to pull out the wrench and take a few seconds longer on most fasteners, compared to twisting off a bolt and the resultant hassles getting it out...As always, YMMV :) 8)

And I use a lot of the blue Loctite, too, Steve. :D

Mark
 
For my 750 the Real Gasket torque was about 9 inch pounds. I bought a Park deflection beam torque wrench that works pretty well. Bicycle shops or on-line stores are the best source for Parks.

I also have a 0-150 ft-lb old Craftsman deflection beam, and a Craftsman 5-80 ft- lb microadjusting torque wrench.

These pretty well cover all of my needs.

Mike
 
I use a torque wrench for everything that has a spec. I guess someone thought it was important.

I can get 3/8 drive, low range, "set and click" torque wrenches for about $40 Cdn. at Princess Auto.
If anyone's interested, let me know.
They are back ordered at the moment but they expect more in 2 weeks.

Mine has worked great so far. :)
 
I use a torque wrench for everything that has a spec. I guess someone thought it was important.

I can get 3/8 drive, low range, "set and click" torque wrenches for about $40 Cdn. at Princess Auto.
If anyone's interested, let me know.
They are back ordered at the moment but they expect more in 2 weeks.

Mine has worked great so far. :)
 
Where can you get a torque wrench calibrated? I have a pair of craftsman twist-dial types (one to 150ft/lbs, the other to 250in/lbs) but I have never calibrated them.
 
You could ask around at an aircraft hangar if you live near a small one. I'm not sure what you'd look for under the yellow pages.

Steve
 
morthrane said:
Where can you get a torque wrench calibrated? I have a pair of craftsman twist-dial types (one to 150ft/lbs, the other to 250in/lbs) but I have never calibrated them.
Click to expand...

Cornerstone Metrology Service
7625 Hayvenhurst Ave., Unit 33
Van Nuys, CA 91406
818-902-9551

or

Here...
 
morthrane said:
Where can you get a torque wrench calibrated? I have a pair of craftsman twist-dial types (one to 150ft/lbs, the other to 250in/lbs) but I have never calibrated them.
Click to expand...

I had Sears calibrate a Craftsman Digitork once after it had been dropped. It took 6 months to get it back.

Hap
 
You must log in or register to reply here.
Back
Top