.png "Powered by vBulletin")
Does anyone know where the black rubberized washers go that come with a gasket set? There are 4 of them.
-
-
Two on the cover for the oil distribution cavity (where the oil pressure sensor screws into). I think another is used on the cam chain tensioner rub block, and I'm not sure where else, cam chain tensioner maybe (or similar).Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection -
4 outer screws on the valve cover on my
E
Part #6Comment
-
I guess I should have asked does anything go between the copper on my cylinder head gasket?
Gasket_zpse2651c06.jpgComment
-
I would have replied this morning but expected at least a few dozen replies by now. Sorry.
It looks like you figured out that they go on the outer four studs.Comment
-
They seem to move around. Does the gasket go on first then the washers on top?Comment
-
Can you post photos of the washers you are referring to? I thought you meant the small metal washers with the rubber in the middle, but it seems this was incorrect.Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-ResurrectionComment
-
they are metal with rubber in the middle. Do they just sit on the copper. I tried to post more but the system would not let me.Comment
-
Sorry, I misunderstood as wellComment
-
I have no experience with those seals but it certainly appears that they would fit around those outer cylinder studs. Not sure why they would lay on top of the copper though.Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-ResurrectionComment
-
I have no idea where those washers would go, but they do not sit on top of the copper washers located in the head gasket. There should be four o-rings that fit inside the copper washers.
I assume this is an aftermarket gasket set?Comment
-
Well, I'm flummoxed. No clue where those seals go.Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-ResurrectionComment
-
More importantly at this point is am I missing some seals that go inside the copper rings.Comment
-
Yes you are.Comment
-
Hi rustybronco, do you see the picture that I posted that had the one washer, that washer has rubber on the inside. The outside of the washer does not fit inside the copper does it sit on top or should it fit inside?Comment
Comment