Announcement

Collapse
No announcement yet.

78 GS1000 Fuel Sending Unit

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    78 GS1000 Fuel Sending Unit

    On the sending unit on the fuel tank is a nipple where a drain or vacuum hose would go. What is the tube? Its been so long since I took the bike apart that I cant remember. Thanks, Jim
    Tags: None
    #2
    Vinyl, used as a drain in case the sender or gasket leaks.
    De-stinking Penelope http://thegsresources.com/_forum/sho...d.php?t=179245

    http://www.thegsresources.com/_forum...35#post1625535

    Comment

      #3
      A vinyl tube will probably work, as it should never see any fuel running through it, but the original tube was rubber.

      .
      sigpic
      mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
      hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
      #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
      #2 son: 1980 GS1000G
      Family Portrait
      Siblings and Spouses
      Mom's first ride
      Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
      (Click on my username in the upper-left corner for e-mail info.)

      Comment

        #4
        and it runs back and down by the airbox
        1978 GS 1000 (since new)
        1979 GS 1000 (The Fridge, superbike replica project)
        1978 GS 1000 (parts)
        1981 GS 850 (anyone want a project?)
        1981 GPZ 550 (backroad screamer)
        1970 450 Mk IIID (THUMP!)
        2007 DRz 400S
        1999 ATK 490ES
        1994 DR 350SES

        Comment

          #5
          Originally posted by Big T View Post
          and it runs back and down by the airbox
          and away from the exhaust.
          sigpicMrBill Been a GSR member on and off since April 2002
          1980 GS 750E Bought new in Feb of 1980
          2015 CAN AM RTS


          Stuff I've done to my bike:dancing: 1100E front end with new Sonic springs, 1100E swing arm conversion with new Progressive shocks installed, 530 sprockets/chain conversion, new SS brake lines, new brake pads. New SS fasteners through out. Rebuilt carbs, new EBC clutch springs and horn installed. New paint. Motor runs strong.

          Comment

            #6
            I would suggest fresh tank gaskets to ensure there isnt any catastrophic failures in the first place. But I would run the tube out center of the engine and between the swing arm. like was mentioned, should it ever dump you dont want it gushing on a hot pipe.
            MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
            1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

            NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


            I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

            Comment

              #7
              Cool, I'll run a long hose down. Its funny what you forget when a project gets pushed to the side for a few years. thanks, Jim

              Comment

                #8
                Make sure to route the drain tube to the side of the rear wheel too for obvious reasons.
                Ed

                To measure is to know.

                Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

                Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

                Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

                KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

                Comment

                Previous template Next
                Working...
                X