De-stinking Penelope

[chuck hahn]

Too funny on the petcock Dale...And Pete, the "mess" on the frame was all over the seat and tank. I had wiped a good bit of it off the tank the morning Dale was on his way to get it. It was a sight thats for sure.

[SVSooke]

Dale the more I see the less bad my sad sack CB750F looks

[rustybronco]

Thanks Greg! Just what I needed to hear.

Tried the swing arm 'cheater' slide hammer trick on the rotor, but so far now luck a getting it to come off.

[SVSooke]

Hey your was together,mines was mostly in bits I didn't take apart.Getting the carbs back together looks like it might be very very interesting.

[chuck hahn]

Dale...its a 14MM X 1.25 pitch i believe..If you get a hardened one and turn it all the way in till it presses against the crank and then tighten it real good. Then smack the end of the bolt a bit..the vibrations help loosen it from the end of the crank. Then do the slide hammer if it doesnt loosen itself off.

[pete]

Too funny on the petcock Dale...And Pete, the "mess" on the frame was all over the seat and tank. I had wiped a good bit of it off the tank the morning Dale was on his way to get it. It was a sight thats for sure.

Ugh I see... horrid! However I have confidence Dale can make it all shiny and new

Thanks Greg! Just what I needed to hear.

Tried the swing arm 'cheater' slide hammer trick on the rotor, but so far now luck a getting it to come off.

Dale, please be careful! That's how I did some serious damage to my thumb, that exact same method.

If you want a reminder, I have a photo...

[rustybronco]

Dale...its a 14MM X 1.25 pitch i believe..If you get a hardened one and turn it all the way in till it presses against the crank and then tighten it real good.

Chuck, If it had a blind hole I would have just put a socket in it and tightened the swing arm bolt against it. Unfortunately the hole goes all the way through the crankshaft. I need to get a tap so I can fix the top thread that got slightly damaged when I put a 1/4" extension in the hole in order to give the swing arm bolt something to press against.

I brought the rotor retaining bolt and my dial calipers so I can order a tap to clean up the threads. Thanks for the size, it should help.

[chuck hahn]

The valve cover is packaged and will be shippied out this morning. Could be a 16 MM too but if you had to rethread id you could make it whatever is conveinent.

[chuck hahn]

This is basically what the suzuki one looks like too..the one pictured is for the Yamaha but you get the idea...

http://www.bing.com/images/search?q=suzuki+motorcycle+rotor+puller&view=detail&id=FD21CC02EB184B4C75D61C1B62129481007CF75E&first=0&qpvt=suzuki+motorcycle+rotor+puller&FORM=IDFRIR

See the one marked Yamaha, Suzuki, Kwasaki here...

http://www.shopping.com/rotor-puller-suzuki/products

[rustybronco]

http://www.ebay.com/itm/150730209160...84.m1438.l2649

Cheapest one I've found so far.

[chuck hahn]

Im not understanding...so whats that big belled thing do? Just take a bolt and weld a few big nuts that will fit thru the rotor hole on the end and screw it in. Maybe a bit of heat on the crank end and give it a few smacks and then re torque it..should just pop off the end of the crank.

EDIT...Or weld the nuts on and grind the flats off so they will fit thru..AND you can fill in the center of the bolts to make a nice flat end to press against the crank.

[rustybronco]

Im not understanding...so whats that big belled thing do?

It threads onto the outside of the flywheel (rotor's) hub, instead of grabbing the inside threads of the flywheel.

like this...

[chuck hahn]

Wonder if anyone has tried a pickle fork kind of arrangement???

[rustybronco]

My project took a turn for the worse...

Needs a crankshaft and possibly more after I split the cases.

[Nessism]

Ouch!